[Asterisk-Users] TDM31B has no interrupts?

[Rich Adamson]

The output from lspci should have shown something like:
 02:0a.0 Communication controller: Tiger Jet Network Inc. Intel 537
and its not there. Time to call/write digium support; suspect a
bad card and probably related to pci bus, but that's a guess.

------------------------
> Hi,
> 
> Thanks for taking time to answer.
> 
>     > Not enough info in the above to hint at the problem. What linux
>     > distro,
> 
> SuSE Linux 8.2 2.4.20-4GB
> 
>     > what does your /etc/zaptel look like,
> 
> For the TDM22B card:
> 
> fxoks=1-2
> fxsks=3-4
> loadzone = uk
> defaultzone=uk
> 
>     > zapata.conf
> 
> signalling=fxo_ks
> echocancel=yes
> echocancelwhenbridged=yes
> echotraining=400
> callprogress=yes
> busydetect=1
> busycount=7
> relaxdtmf=yes
> channel => 1,2
> signalling=fxs_ks
> group=2
> context=incoming
> channel=> 3,4
> 
>     > , what steps did you take to start the drivers (eg, modprobe,
>     > ztcfg), etc.
> 
> linux:~ # modprobe zaptel
> Warning: loading /lib/modules/2.4.20-4GB/misc/zaptel.o will taint the
> kernel: no license
>   See http://www.tux.org/lkml/#export-tainted for information about
> tainted modules
> Module zaptel loaded, with warnings
> linux:~ # modprobe wctdm
> Warning: loading /lib/modules/2.4.20-4GB/misc/wctdm.o will taint the
> kernel: no license
>   See http://www.tux.org/lkml/#export-tainted for information about
> tainted modules
> Module wctdm loaded, with warnings
> linux:~ # ztcfg -vvv
> 
> Zaptel Configuration
> ======================
> 
> 
> Channel map:
> 
> Channel 01: FXO Kewlstart (Default) (Slaves: 01)
> Channel 02: FXO Kewlstart (Default) (Slaves: 02)
> Channel 03: FXS Kewlstart (Default) (Slaves: 03)
> Channel 04: FXS Kewlstart (Default) (Slaves: 04)
> 
> 4 channels configured.
> 
> linux:~ #
> 
>     > Since we're forced to guess at that stuff, here's a list of things
>     > that might have an impact.
>     > - ensure the definitions in /etc/zaptel.conf are reasonable
> 
> Hope they are.
> 
>     > - run ztcfg -vvv from the command line. Any errors?
> 
> No errors as above.
> 
>     > - run 'modprobe wctdm', any errors?
> 
> The only message that shows is a warning about the kernel being tainted.
> I checked the link I was referred to and it should really have no effect
> on the operation of the card (s).
> 
>     > - what does dmesg, lspci, and lsmod output say?
> 
> 	dmesg:
> Zapata Telephony Interface Registered on major 196
> Freshmaker version: 71
> Freshmaker passed register test
> Module 0: Installed -- AUTO FXS/DPO
> Module 1: Installed -- AUTO FXS/DPO
> Module 2: Installed -- AUTO FXO (FCC mode)
> Module 3: Installed -- AUTO FXO (FCC mode)
> Found a Wildcard TDM: Wildcard TDM400P REV H (4 modules)
> Registered tone zone 4 (United Kingdom)
> Registered tone zone 4 (United Kingdom)
> 
> 	lspci:
> 00:00.0 Host bridge: VIA Technologies, Inc. P4M266 Host Bridge
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
> 00:0a.0 Communication controller: Tiger Jet Network Inc. Intel 537
> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
> 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus
> Master IDE (rev 06)
> 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97
> Audio Controller (rev 50)
> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev
> 74)
> 01:00.0 VGA compatible controller: S3 Inc. [ProSavageDDR K4M266]
> 
> 	lsmod:
> Module                  Size  Used by    Tainted: P
> wctdm                  25568   0  (unused)
> zaptel                183616   0  [wctdm]
> snd-pcm-oss            45888   0  (autoclean)
> snd-mixer-oss          13560   0  (autoclean) [snd-pcm-oss]
> isa-pnp                29672   0  (unused)
> ipv6                  134388  -1  (autoclean)
> raw1394                14516   0  (unused)
> ieee1394               32880   0  [raw1394]
> via-rhine              12176   1
> mii                     2304   0  [via-rhine]
> snd-via8233            12516   0
> snd-pcm                62912   0  [snd-pcm-oss snd-via8233]
> snd-timer              11904   0  [snd-pcm]
> snd-ac97-codec         31152   0  [snd-via8233]
> snd-mpu401-uart         3360   0  [snd-via8233]
> snd-rawmidi            13824   0  [snd-mpu401-uart]
> snd-seq-device          4000   0  [snd-rawmidi]
> snd                    35940   0  [snd-pcm-oss snd-mixer-oss snd-via8233
> snd-pcm snd-timer snd-ac97-codec snd-mpu401-uart snd-rawmidi
> snd-seq-device]
> soundcore               3396   0  [snd]
> reiserfs              200532   1
> 
>     > - what does zttool show?
> 
> I realized I need the package "libnewt" to get this to compile.  Meanwhile
> does the above information reveal anything?  Is there any BIOS setting I
> need to tweak?
> 
> Thanks in advance.
> 
> Rgds,
> Gerald.
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users

---------------End of Original Message-----------------