[Asterisk-Users] TDM31B has no interrupts?

[Begumisa Gerald M]

Hi,

Thanks for taking time to answer.

    > Not enough info in the above to hint at the problem. What linux
    > distro,

SuSE Linux 8.2 2.4.20-4GB

    > what does your /etc/zaptel look like,

For the TDM22B card:

fxoks=1-2
fxsks=3-4
loadzone = uk
defaultzone=uk

    > zapata.conf

signalling=fxo_ks
echocancel=yes
echocancelwhenbridged=yes
echotraining=400
callprogress=yes
busydetect=1
busycount=7
relaxdtmf=yes
channel => 1,2
signalling=fxs_ks
group=2
context=incoming
channel=> 3,4

    > , what steps did you take to start the drivers (eg, modprobe,
    > ztcfg), etc.

linux:~ # modprobe zaptel
Warning: loading /lib/modules/2.4.20-4GB/misc/zaptel.o will taint the
kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about
tainted modules
Module zaptel loaded, with warnings
linux:~ # modprobe wctdm
Warning: loading /lib/modules/2.4.20-4GB/misc/wctdm.o will taint the
kernel: no license
  See http://www.tux.org/lkml/#export-tainted for information about
tainted modules
Module wctdm loaded, with warnings
linux:~ # ztcfg -vvv

Zaptel Configuration
======================


Channel map:

Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXO Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)

4 channels configured.

linux:~ #

    > Since we're forced to guess at that stuff, here's a list of things
    > that might have an impact.
    > - ensure the definitions in /etc/zaptel.conf are reasonable

Hope they are.

    > - run ztcfg -vvv from the command line. Any errors?

No errors as above.

    > - run 'modprobe wctdm', any errors?

The only message that shows is a warning about the kernel being tainted.
I checked the link I was referred to and it should really have no effect
on the operation of the card (s).

    > - what does dmesg, lspci, and lsmod output say?

	dmesg:
Zapata Telephony Interface Registered on major 196
Freshmaker version: 71
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1: Installed -- AUTO FXS/DPO
Module 2: Installed -- AUTO FXO (FCC mode)
Module 3: Installed -- AUTO FXO (FCC mode)
Found a Wildcard TDM: Wildcard TDM400P REV H (4 modules)
Registered tone zone 4 (United Kingdom)
Registered tone zone 4 (United Kingdom)

	lspci:
00:00.0 Host bridge: VIA Technologies, Inc. P4M266 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
00:0a.0 Communication controller: Tiger Jet Network Inc. Intel 537
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus
Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97
Audio Controller (rev 50)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev
74)
01:00.0 VGA compatible controller: S3 Inc. [ProSavageDDR K4M266]

	lsmod:
Module                  Size  Used by    Tainted: P
wctdm                  25568   0  (unused)
zaptel                183616   0  [wctdm]
snd-pcm-oss            45888   0  (autoclean)
snd-mixer-oss          13560   0  (autoclean) [snd-pcm-oss]
isa-pnp                29672   0  (unused)
ipv6                  134388  -1  (autoclean)
raw1394                14516   0  (unused)
ieee1394               32880   0  [raw1394]
via-rhine              12176   1
mii                     2304   0  [via-rhine]
snd-via8233            12516   0
snd-pcm                62912   0  [snd-pcm-oss snd-via8233]
snd-timer              11904   0  [snd-pcm]
snd-ac97-codec         31152   0  [snd-via8233]
snd-mpu401-uart         3360   0  [snd-via8233]
snd-rawmidi            13824   0  [snd-mpu401-uart]
snd-seq-device          4000   0  [snd-rawmidi]
snd                    35940   0  [snd-pcm-oss snd-mixer-oss snd-via8233
snd-pcm snd-timer snd-ac97-codec snd-mpu401-uart snd-rawmidi
snd-seq-device]
soundcore               3396   0  [snd]
reiserfs              200532   1

    > - what does zttool show?

I realized I need the package "libnewt" to get this to compile.  Meanwhile
does the above information reveal anything?  Is there any BIOS setting I
need to tweak?

Thanks in advance.

Rgds,
Gerald.