[Asterisk-Users] Snom 200 phones not working.

[listas iPfone]

Hi

I sugest you to make a reset and switch off  the phone before upgrade.

It solved many problems for me.

Miklos



----- Original Message ----- 
From: "Rich Adamson" <radamson at routers.com>
To: <asterisk-users at lists.digium.com>
Sent: Friday, January 23, 2004 11:32 AM
Subject: Re: [Asterisk-Users] Snom 200 phones not working.


> Ariel,
>
> > I have 2 Snom 200 and would like to get them to work properly with
> > Asterisk.  With the Firmware 2.02t I am able to use the phone.  But only
> > one line configured.  With there newer firmware 2.03o it will not allow
> > me to make calls.  But I can get calls on the unit.  Again the 2nd line
> > is not able to be registered.  Is this an issue with Asterisk or Snom?
> >
> > I could use some example configuration files.  I have followed the Snom
> > FAQ step by step.  But it's still not working.
>
> I just upgraded my 200 to v2.03o and its working fine with two extns
> defined. I happen to be using * CVS-12/04/03-14:24:40 on the same wire
> (no nat, etc).
>
> My sip.conf entries look like:
> [3007]
> type=friend
> host=dynamic
> username=3007
> secret=mypassword
> context=from-sip
>
> [3008]
> type=friend
> host=dynamic
> username=3008
> secret=mypassword
> context=from-sip
>
> Using your web browser to config the phone, verify:
> Settings/SIP/Lines
>   Account = 3007 (to match above sip.conf def)
>   Registrar = ip address of asterisk box
>   Action = proxy
>   Account = 3008 (to match above sip.conf def)
>   Registrar = ip address of asterisk box
>   Action = proxy
> Settings/SIP/Stack
>   Outbound Proxy, Registrar is outbound proxy = yes
> Settings/SIP/Authentication
>   Line 1, Realm = asterisk, Username = 3007, Pasword = mypassword
>   Line 2, Realm = asterisk, Username = 3008, Pasword = mypassword
> Settings/Key Mapping
>   P1 = Line, Number = 3007
>   P2 = Line, Number = 3008
>
> After ensuring your phone settings actually match the sip.conf settings
> and that you've properly selected "Save" after changing each of the above
> entries in the phone, then reboot the phone. If the phone prompts you to
> download another firmware image, simply press ESC. (Seems some config
> changes don't take effect until after a phone reboot.)
>
> The above config has been working fine with the last several (estimate
> about 10) firmware versions, however the "user" interaction with several
of
> the keys are rather non-intuitive (or even backwards) for US users.
>
> For example, if you answer an incoming call on Line 1 (x3007 above) and
place
> that call on hold using the "Hold" key, then select Line 2 (x3008) to do a
> consultive call to a different extn, you have to press the ESC key to hang
> up that second consultive call.  If instead of pressing the ESC key you
> simply press Line 1 to return to the original call, Line 2 is
automatically
> put on hold (instead of dropping the line as it does in the US). If you're
> not paying attention to the LEDs, you've now tied up the second line/extn
> until such time as you muck around to release it.
>
> If that second (consultive) call happens to be to a pstn user and your
> Central Office supports calling-party line supervision, you've probably
> tied up that person's telephone line as well. (Email comments to snom
> resulted in push-back, suggesting the ESC key is the proper way to drop
> that second line. I'd guess US users (not techie's) will object to using
> the phone in any form of production telephony.)
>
> I've not tried the 200 with the later CVS versions, so don't have a clue
as
> to what you're milage may be.
>
> Rich
>
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>