[Asterisk-Users] Cisco 2600 and ASTERISK

[Brian West]

This is inbound FXO's pointed at the autoattendat on our * server.

On Wed, 24 Sep 2003, Doug Dimick wrote:

> The configuration shouldn't be much different. Just replace port 1/0/0
> with port 1/0:23, or whatever the voice port your PRI/T1/E1 happens to be.
>
> PLAR is Private Line Auto Ringdown. You pick up the port and it
> automatically dials. Think Batphone. In the configuration provided below
> it is configured so that anyone picking up the phone on the voice port
> (like an incoming phone call) will automatically dial 9999, which then
> would connect to the IP address of Asterisk with H.323.
>
>      -d
>
>
> > Message: 4
> > Date: Wed, 24 Sep 2003 16:31:17 +0000 (GMT)
> > From: Sean Figgins <sfiggins at mail.celicas.org>
> > To: asterisk-users at lists.digium.com
> > Subject: RE: [Asterisk-Users] Cisco 2600 and ASTERISK
> > Reply-To: asterisk-users at lists.digium.com
> >
> >
> > That is about what I have been seing for help.  Has anyone any clue what
> > to di with a 2600 that has a T1 adapter on a high-density high-density
> > voice port adapter?
> >
> > BTW...  Because I am lazy, what does plar do?
> >
> > -Sean
> >
> > On Wed, 24 Sep 2003, Brian West wrote:
> >
> >> This is simple to do..
> >>
> >> voice-port 1/0/0
> >>  connection plar 9999
> >> !
> >> voice-port 1/0/1
> >>  connection plar 9999
> >> !
> >> dial-peer voice 1000 voip
> >>  max-conn 4
> >>  destination-pattern 9999
> >>  req-qos guaranteed-delay
> >>  codec g711ulaw
> >>  ip precedence 5
> >>  no vad
> >>  session target ipv4:x.x.x.x
> >> !
> >>
> >> in h323.conf set the context=blah
> >>
> >> [blah]
> >>
> >> exten => 9999,1,Goto(s,1)
> >>
> >>
> >> Done... its really that simple.  I have this working with a 2600 and a
> >> 1750.
> >>
> >> bkw
> >>
> >> On Wed, 24 Sep 2003, Joseph Finley wrote:
> >>
> >> > I too would like to see it.  I've tried many times with the help of a
> >> few
> >> > and never got it to work.  It always results in a fast busy.
> >> >
> >> > Joe
> >> >
> >> >
> >> > -----Original Message-----
> >> > From: asterisk-users-admin at lists.digium.com
> >> > [mailto:asterisk-users-admin at lists.digium.com] On Behalf Of Bartosz
> >> Jozwiak
> >> > Sent: Wednesday, September 24, 2003 9:46 AM
> >> > To: ASTERISK USERS
> >> > Subject: [Asterisk-Users] Cisco 2600 and ASTERISK
> >> >
> >> >
> >> > Hello,
> >> >
> >> > Could somebody tell me if I can connect CISCO 2600 router with support
> >> of
> >> > H.323 to Asterisk ?
> >> > If it is possible could somebody tell me how to do it.
> >> > I would like to document it and put on some website so everyone can
> >> see it.
> >> >
> >> > Regards,
> >> >
> >> > -- bart
> >> >
> >> >
> >> _______________________________________________
> >> Asterisk-Users mailing list
> >> Asterisk-Users at lists.digium.com
> >> http://lists.digium.com/mailman/listinfo/asterisk-users
> >>
> >
> >
> >
> > --__--__--
> >
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> >
> >
> > End of Asterisk-Users Digest
> >
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
>