[Asterisk-Users] use of SIP SHOW CHANNELS question

[CW_ASN]

How about 'show translations' command?

This machine doesn't have G.729 codec licenses...
AFAIK, this command calculates the cost for each translation...

noc2pbx*CLI> show translation
         Translation times between formats (in milliseconds)
          Source Format (Rows) Destination Format(Columns)

           G723    GSM   ULAW   ALAW  ADPCM  SLINR  LPC10  G729A  SPEEX
ILBC

23      -      -      -      -      -      -      -      -      -      -
     GSM      -      -      2      2      2      1     13      -      -
38
    ULAW      -      6      -      1      2      1     13      -      -
38
    ALAW      -      6      1      -      2      1     13      -      -
38
     MP3      -     15     11     11     11     10     22      -      -
47
   ADPCM      -      6      2      2      -      1     13      -      -
38
   SLINR      -      5      1      1      1      -     12      -      -
37
   LPC10      -      9      5      5      5      4      -      -      -
41

9A      -      -      -      -      -      -      -      -      -      -

EX      -      -      -      -      -      -      -      -      -      -
    ILBC      -     11      7      7      7      6
8      -      -      -
noc2pbx*CLI>

And this machine has G.729 loaded:

noc2pbx2*CLI> show translation
         Translation times between formats (in milliseconds)
          Source Format (Rows) Destination Format(Columns)

           G723    GSM   ULAW   ALAW  ADPCM  SLINR  LPC10  G729A  SPEEX
ILBC
    G723      -     62     56     56     56     55     64    106      -
106
     GSM    240      -      3      3      3      2     11     53      -
53
    ULAW    239      8      -      1      2      1     10     52      -
52
    ALAW    239      8      1      -      2      1     10     52      -
52
     MP3    258     27     21     21     21     20     29     71      -
71
   ADPCM    239      8      2      2      -      1     10     52      -
52
   SLINR    238      7      1      1      1      -      9     51      -
51
   LPC10    245     14      8      8      8      7      -     58      -
58
   G729A 100237 100006 100000 100000 100000  99999 100008      -      -
100050

EX      -      -      -      -      -      -      -      -      -      -
    ILBC    247     16     10     10     10      9     18
0      -      -
noc2pbx2*CLI>



Regards,

Gus

----- Original Message -----
From: "Tilghman Lesher" <tilghman at mail.jeffandtilghman.com>
To: <asterisk-users at lists.digium.com>
Sent: Sunday, October 19, 2003 11:44 PM
Subject: Re: [Asterisk-Users] use of SIP SHOW CHANNELS question


> On Sunday 19 October 2003 21:30, Andrew Kohlsmith wrote:
> > > *CLI> show codec 4
> > > No such command 'show codec' (type 'help' for help)
> > > *CLI> show audio codecs
> > > No such command 'show audio' (type 'help' for help)
> >
> > Rebuild your system.  I had that happen and my Makefile was screwed
> > up and didn't actually build any codecs.
>
> Stop already.  The command serves only as a translation table.  It does
> NOT, repeat NOT, repeat NOT, suggest anything about which codecs
> are actually loaded.
>
> If you actually run this now, you should get the following message on
> your console (put there SPECIFICALLY because people were confusing
> what the command actually does):
>
> Disclaimer: this command is for informational purposes only.
>         It does not indicate anything about your configuration.
>
> -Tilghman
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users