[Asterisk-Users] fxs no dial tone on my USB device

[Mark Spencer]

Sometimes these S100U's seem to just die, usually preceeded by a period in
which the audio starts getting substantially poorer.  Not sure why this
happens (it only seems to happen on a relatively small number of them --
maybe a dozen so far of all the ones we've shipped) but all the failures
manifest themselves in approximately the same way.

Of course the device is covered by a 2 years warranty from Digium so feel
free to get an RMA number to exchange the device for a new one.

Mark

On 18 May 2003, Steven Smith wrote:

> That usually works for me also - but its not working this time. I've
> rebooted, unplugged the USB connector and reinstalled drivers not seems
> to get it back going.
>
>
> On Sun, 2003-05-18 at 00:30, Jeremy McNamara wrote:
> > This is the typical problem that lots of people have with the S100U.
> > What I've done is rmmod all the modules and unplug/replug the USB
> > device, run ztcfg, then start Asterisk.  This procdure works most of the
> > time for me,  YMMV.
> >
> > Jeremy McNamara
> >
> >
> > Steven Smith wrote:
> >
> > >My USB FXS adapter is not giving out any dialtone or ringing. I didn't
> > >see a resolution to this issue.I have an email pending with support.
> > >
> > >If someone can forward me the resolution to this issue I would
> > >appreciate it -vvvvvvvv much :) ?
> > >
> > >The driver loads properly but asterisk never sees it going off hook and
> > >no dialtone. Asterisk also see it as an active channel - zttool shows it
> > >ok.
> > >
> > >
> > >
> > >
> > >On Thu, 2003-05-15 at 17:05, Martin Pycko wrote:
> > >
> > >
> > >>When you type "zap show channels" on the asterisk console do you see your
> > >>USB channel ?
> > >>
> > >>Martin
> > >>
> > >>On 16 May 2003, Brancaleoni Matteo wrote:
> > >>
> > >>
> > >>
> > >>>asterisk starts ok?
> > >>>
> > >>>matteo
> > >>>
> > >>>Il gio, 2003-05-15 alle 23:29, Cristian Rodriguez ha scritto:
> > >>>
> > >>>
> > >>>>Hello,
> > >>>>
> > >>>>Yes I checked the mail list archives
> > >>>>Yes I have the latest CVS code
> > >>>>
> > >>>>I cannot get a dial tone from my USB FXS device.
> > >>>>
> > >>>>In my search through the list achives I found that it has been an issue with
> > >>>>some others.
> > >>>>
> > >>>>I ensured the modules where loaded in the right order.  I managed to get
> > >>>>sound when I press the keys on the phone, but still no dialtone.
> > >>>>I used the astinstall script that came with my dev lite kit.  (The FXO PCI
> > >>>>board is working fine)
> > >>>>
> > >>>>I tried unloading the modules and reloading them then ztcfg but still no
> > >>>>dialtone.
> > >>>>
> > >>>>I am trying the install on a new box to elimitate the USB controller as one
> > >>>>of the posibilities.
> > >>>>
> > >>>>I am using the sample configs.  Perhaps I have not setup my extensions
> > >>>>properly.
> > >>>>
> > >>>>PII 350 64 meg ram redhat 9.0 dev lite kit. USB usb-ohci.c: usb-00:09.0,
> > >>>>OPTi Inc. 82C861
> > >>>>
> > >>>>Can someone please help.
> > >>>>
> > >>>>_______________________________________________
> > >>>>Asterisk-Users mailing list
> > >>>>Asterisk-Users at lists.digium.com
> > >>>>http://lists.digium.com/mailman/listinfo/asterisk-users
> > >>>>
> > >>>>
> > >>>_______________________________________________
> > >>>Asterisk-Users mailing list
> > >>>Asterisk-Users at lists.digium.com
> > >>>http://lists.digium.com/mailman/listinfo/asterisk-users
> > >>>
> > >>>
> > >>>
> > >>_______________________________________________
> > >>Asterisk-Users mailing list
> > >>Asterisk-Users at lists.digium.com
> > >>http://lists.digium.com/mailman/listinfo/asterisk-users
> > >>
> > >>
> > >
> > >
> > >_______________________________________________
> > >Asterisk-Users mailing list
> > >Asterisk-Users at lists.digium.com
> > >http://lists.digium.com/mailman/listinfo/asterisk-users
> > >
> > >
> >
>
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
>