[Asterisk-Users] fxs card not loading in new computer

[Mark Spencer]

Just tell it to use wcfxs or something instead of torisa.  most people
load the driver and don't count on autoloading of modules by the kernel
when they run asterisk.

Mark

On Thu, 12 Jun 2003, Steve wrote:

> Well after moving to a diff slot and rebooting twice I finally got:
>
> Zapata Telephony Interface Registered on major 196
> No ISA tormenta card found at 0d000
> Zapata Telephony Interface Unloaded
> CSLIP: code copyright 1989 Regents of the University of California
> PPP generic driver version 2.4.2
> Zapata Telephony Interface Registered on major 196
> No ISA tormenta card found at 0d000
> Zapata Telephony Interface Unloaded
> CSLIP: code copyright 1989 Regents of the University of California
> PPP generic driver version 2.4.2
> Zapata Telephony Interface Registered on major 196
> Zapata Telephony Interface Unloaded
> Zapata Telephony Interface Registered on major 196
> PCI: Assigned IRQ 10 for device 00:06.0
> Found a Wildcard FXO: Wildcard X101P
> PCI: Assigned IRQ 5 for device 00:0a.0
> Freshmaker version: 62
> Freshmaker passed register test
> Module 0: Initialized
> Module 1: Not installed
> Module 2: Not installed
> Module 3: Not installed
> Found a Wildcard FXS: Wildcard S400P Prototype (4 modules)
> Registered tone zone 0 (United States / North America)
>
> Though it still complained that no Tormenta card found at 0d000.
> Both cards use an interrupt and ioport. So I modified modules.conf to use
> the ioport (e100) with no luck. What address should it be using?
>
>
> On Thursday 12 June 2003 11:03 am, Steve wrote:
> > (I'm producing a writeup on all the things one run into building an *
> > box. Which after a couple of boxes is showing up aplenty.)
> >
> > So this uses the working h/w and config's from another box. All I do is
> > build in a new computer.
> >
> > Loading the modules I got:
> > __________________________________________________
> > Zaptel Configuration
> > ======================
> >
> >
> > Channel map:
> >
> > Channel 01: FXS Kewlstart (Default) (Slaves: 01)
> > Channel 02: FXO Kewlstart (Default) (Slaves: 02)
> >
> > 2 channels configured.
> >
> > ZT_CHANCONFIG failed on channel 1: No such device or address (6)
> > __________________________________________________
> > So I made sure that the fxo is loaded first. Now it complains on channel
> > 2. I also ran ztcfg -vv but no diff. So I ran dmesg which shows
> >
> > Zapata Telephony Interface Registered on major 196
> > No ISA tormenta card found at d0000
> > Zapata Telephony Interface Unloaded
> >
> > a few times. And:
> >
> > Zapata Telephony Interface Registered on major 196
> > PCI: Assigned IRQ 10 for device 00:06.0
> > Found a Wildcard FXO: Wildcard X101P
> > PCI: Assigned IRQ 5 for device 00:09.0
> >
> > also a few times. Verified that 196 was torisa. Looking for address or
> > irq problems I found that only the fxo card occupied an interrupt. 5 is
> > not in use. Iomem and ioport revealed:
> >
> > fe102000-fe102fff : Tiger Jet Network Inc. Model 300 128k (#2)
> > fe103000-fe103fff : Tiger Jet Network Inc. Model 300 128k
> >
> > e400-e4ff : Tiger Jet Network Inc. Model 300 128k (#2)
> > e800-e8ff : Tiger Jet Network Inc. Model 300 128k
> >   e800-e8fe : wcfxo
> >
> > /etc/modules.conf has:
> >
> > options torisa base=0xd0000
> > alias char-major-196 torisa
> > post-install tor2 /sbin/ztcfg
> > post-install wcfxo /sbin/ztcfg
> > post-install wct1xxp /sbin/ztcfg
> > post-install wcfxs /sbin/ztcfg
> > post-install wcfxsusb /sbin/ztcfg
> > post-install torisa /sbin/ztcfg
> >
> > It seems that d000 is the wrong address but it does not wrk on e400 or
> > e800, so I'm stomped.
>
> --
>
> Steve
> ______________________________________
> This sig is pending approval
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
>