[Asterisk-Users] RE: T100P/ TSU 600 installation problem

[jerk face]

Oops ... I found out my problem
span=....

--- jerk face <jerkface2098 at yahoo.com> wrote:
> I am using a crossover cable.
> My channel definitions are:
> fxoks=1-22
> fxsks=23-24
> in zaptel.conf
> 
> 
> --- Alex Lopez <alex at opsys.com> wrote:
> > 
> > What cable are you using, The SU600 to Digium
> cards
> > need a crossover
> > cable.
> > 
> > 1 to 4
> > 2 to 5
> > 4 to 1
> > 5 to 2
> > 
> > That would stop it from not working,
> > 
> > also make sure that you have a span definition on
> > the zaptel.con file.
> > 
> > 
> > 
> > Message: 7
> > Date: Mon, 25 Aug 2003 12:52:12 -0700 (PDT)
> > From: jerk face <jerkface2098 at yahoo.com>
> > Subject: RE: [Asterisk-Users] T100P/ TSU 600
> > installation problem
> > To: asterisk-users at lists.digium.com
> > Reply-To: asterisk-users at lists.digium.com
> > 
> > Each port is set to the proper signalling type
> (FXO,
> > FXS).  I can't find any other options for the
> > individual ports.
> > As for the timing and configuration of NI, I have
> > tried 
> > NI:
> > Timing Mode as both DTE and NI (my only choices)
> > 
> > Where else should I be checking?
> > (Before this morning, I hadn't even seen a channel
> > bank before, so I'm a little lost at the moment).
> > 
> > Thanks for your time.
> > 
> > --- Wade Weppler <weppler at wwworks-inc.com> wrote:
> > > Have you configured the TSU600 properly?  You
> have
> > > to allocate each FXO/FXS
> > > channel to a timeslot before it will work.  This
> > is
> > > not automatically done
> > > (like the Adtran Total Access series).
> > > 
> > > Mind you, you should still have a sync light on
> > the
> > > T1 card...
> > > 
> > > -wade
> > > 
> > > > -----Original Message-----
> > > > From: asterisk-users-admin at lists.digium.com
> > > [mailto:asterisk-users-
> > > > admin at lists.digium.com] On Behalf Of jerk face
> > > > Sent: Monday, August 25, 2003 3:01 PM
> > > > To: asterisk-users at lists.digium.com
> > > > Subject: RE: [Asterisk-Users] T100P/ TSU 600
> > > installation problem
> > > > 
> > > > My zapata.conf is located in /etc/asterisk and
> > my
> > > > zaptel.conf is located in the /etc directory.
> > > > 
> > > > --- "Adams, Gavin" <gadams at promisant.com>
> wrote:
> > > > > > -----Original Message-----
> > > > > > From: jerk face
> > > [mailto:jerkface2098 at yahoo.com]
> > > > >
> > > > >
> > > > > > I seem to be having a problem with the
> T100P
> > > card.
> > > > >  So
> > > > > > far I have done the following:
> > > > > >
> > > > > > vi zaptel.conf
> > > > > > fxoks=1-22
> > > > > > fxsks=23-24
> > > > > > ...
> > > > > >
> > > > > > vi zapata.conf
> > > > > > ...
> > > > > > signalling=fxo_ks
> > > > > > ...
> > > > > > channel => 1-22
> > > > > > ...
> > > > > > signalling=fxs_ks
> > > > > > ...
> > > > > > channel => 23-24
> > > > > >
> > > > > > I then run
> > > > > > modprobe zaptel
> > > > > > modprobe wct1xxp
> > > > > > ztcfg -vv
> > > > > >
> > > > > > There are no errors to report.  In
> > > /proc/zaptel/1
> > > > > all
> > > > > > of the configured channels are listed.
> > > > >
> > > > > Crazy question, is zaptel.conf is /etc or
> > > > > /etc/asterisk? If the latter,
> > > > > try:
> > > > >
> > > > > 	ztcfg -c /etc/asterisk/zaptel.conf -vvv
> > > > >
> > > > > --- Gavin
> > > > >
> > > > >
> > _______________________________________________
> > > > > Asterisk-Users mailing list
> > > > > Asterisk-Users at lists.digium.com
> > > > >
> > > >
> > >
> >
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> 
> __________________________________
> Do you Yahoo!?
> Yahoo! SiteBuilder - Free, easy-to-use web site
> design software
> http://sitebuilder.yahoo.com
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
>
http://lists.digium.com/mailman/listinfo/asterisk-users


__________________________________
Do you Yahoo!?
Yahoo! SiteBuilder - Free, easy-to-use web site design software
http://sitebuilder.yahoo.com