[Asterisk-Users] Multiple X100P cards

[Jim Archer]

Still no luck with the second X100P card (sigh).  I have tried various 
entries in my zapata.conf file, including:


;use with FXO PCI card
signalling = fxs_ks
txgain = 3
channel => 1-2


And:

;use with FXO PCI card
signalling = fxs_ks
txgain = 3
channel => 1
channel => 2

And:

;use with FXO PCI card
signalling = fxs_ks
txgain = 3
channel => 1

signalling = fxs_ks
txgain = 3
channel => 2


Here is what I get when I try to start Asterisk:


 [chan_zap.so] => (Zapata Telephony w/PRI)
  == Parsing '/etc/asterisk/zapata.conf': Found
DEBUG[16384]: File chan_zap.c, Line 874 (update_conf): Updated conferencing 
on 1, with 0 conference users
    -- Registered channel 1, FXS Kewlstart signalling
WARNING[16384]: File chan_zap.c, Line 554 (zt_open): Unable to specify 
channel 2: No such device or address
ERROR[16384]: File chan_zap.c, Line 4585 (mkintf): Unable to open channel 
2: No such device or address
here = 0, tmp->channel = 0, channel = 2
ERROR[16384]: File chan_zap.c, Line 6154 (load_module): Unable to register 
channel '2'
WARNING[16384]: File loader.c, Line 273 (ast_load_resource): chan_zap.so: 
load_module failed, returning -1
WARNING[16384]: File loader.c, Line 368 (load_modules): Loading module 
chan_zap.so failed!




--On Thursday, April 10, 2003 3:44 PM -0500 Martin Pycko 
<martinp at digium.com> wrote:

> I meant zapata.conf
>
> Martin
>
> On Thu, 10 Apr 2003, Jim Archer wrote:
>
>> Yup, I did.  Here is the entry from zaptel.comf:
>>
>> group => 1
>>
>> fxsks=1-2
>> fxoks=3
>>
>>
>> Here is the output from zap show channels:
>>
>> *CLI> zap show channels
>> Chan. Num. Extension  Context    Language   MusicOnH
>>   1            default    en
>>
>>
>> Any ideas?
>>
>> --On Thursday, April 10, 2003 11:13 AM -0500 Martin Pycko
>> <martinp at digium.com> wrote:
>>
>> > well you have to configure zaptel.conf as well.
>> > Also to see the zap channels you should use "zap show channels"
>> >
>> > Martin
>> >
>> > On Thu, 10 Apr 2003, Jim Archer wrote:
>> >
>> >> Thanks Martin, but I had no luck.  It seems that * des not know there
>> >> is a second X100P card in the machine.  Do I need to tell the drivers
>> >> somehow?
>> >>
>> >>
>> >> *CLI> show channels
>> >>         Channel  (Context    Extension    Pri )   State Appl.
>> >>         Data
>> >>
>> >> 0 active channel(s)
>> >>
>> >>
>> >>
>> >> --On Thursday, April 03, 2003 9:14 AM -0600 Martin Pycko
>> >> <martinp at digium.com> wrote:
>> >>
>> >> > You configure them as usual
>> >> >
>> >> > zaptel.conf
>> >> > fxoks=1-n #(n - how many cards you have)
>> >> >
>> >> > Then you can just plug a single phone line to each of them
>> >> > and then in zttool which one will go into OK from RED state.
>> >> >
>> >> > regards
>> >> > Martin
>> >> >
>> >> > On Thu, 3 Apr 2003, Jim Archer wrote:
>> >> >
>> >> >> Hi All...
>> >> >>
>> >> >> If I have more than 1 X100P card, how do I configure them so I know
>> >> >> which one is which?
>> >>
>> >>
>> >> _______________________________________________
>> >> Asterisk-Users mailing list
>> >> Asterisk-Users at lists.digium.com
>> >> http://lists.digium.com/mailman/listinfo/asterisk-users
>> >>
>> >
>> > _______________________________________________
>> > Asterisk-Users mailing list
>> > Asterisk-Users at lists.digium.com
>> > http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>>
>>
>>
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users