[asterisk-ss7] Issue with Interconnect
Edrich de Lange
edd at edd.za.net
Wed Dec 15 13:58:51 UTC 2010
Basically what I see as the channels
1-7 up
8-15 Down
16 MTP
17-24 up
25-31 down
This seems very simmetrical.
Has anyone seen an issue like this?
I can send calls via it and all
Kind regards
On Wed, Dec 15, 2010 at 1:03 PM, Edrich de Lange <edd at edd.za.net> wrote:
> all are Idle
>
> and
>
>
> [Dec 15 12:55:29] WARNING[5540]: l4isup.c:4803 l4isup_event: Received
> CIC=63 for unequipped circuit (typ=RSC), link 'l2'.
> [Dec 15 12:55:29] WARNING[5540]: l4isup.c:4803 l4isup_event: Received
> CIC=60 for unequipped circuit (typ=RSC), link 'l2'.
> [Dec 15 12:55:29] WARNING[5540]: l4isup.c:4803 l4isup_event: Received
> CIC=62 for unequipped circuit (typ=RSC), link 'l2'.
> [Dec 15 12:55:29] WARNING[5540]: l4isup.c:4803 l4isup_event: Received
> CIC=56 for unequipped circuit (typ=RSC), link 'l2'.
> [Dec 15 12:55:29] WARNING[5540]: l4isup.c:4803 l4isup_event: Received
> CIC=61 for unequipped circuit (typ=RSC), link 'l2'.
> [Dec 15 12:55:29] WARNING[5540]: l4isup.c:4803 l4isup_event: Received
> CIC=57 for unequipped circuit (typ=RSC), link 'l2'.
> [Dec 15 12:55:29] WARNING[5540]: l4isup.c:4803 l4isup_event: Received
> CIC=58 for unequipped circuit (typ=RSC), link 'l2'.
> [Dec 15 12:55:29] WARNING[5540]: l4isup.c:4803 l4isup_event: Received
> CIC=59 for unequipped circuit (typ=RSC), link 'l2'.
>
>
> Kind regards
>
>
>
> On Wed, Dec 15, 2010 at 11:11 AM, Amish <amish at 3g.co.za> wrote:
>> Hi Edrich,
>>
>> What is the current status of those CICs, with ss7 linestat?
>> Idle, Remote Maintenance Blocked, ...
>> What messages are displayed on the console?
>>
>> A.
>>
>>
>> On 12/14/2010 03:52 PM, Edrich de Lange wrote:
>>>
>>> Good morning
>>>
>>> I have an issue on one of the links where I have the last 8 cics not
>>> functioning.
>>>
>>> Can anyone provide details on what may cause this? It works perfectly
>>> fine on my other link.
>>>
>>> I have had the provider also check all their termination equipment,
>>> and that seems to not be the issue. the card has been replaced aswell.
>>>
>>>
>>> Kind regards
>>>
>>>
>>> On Mon, Dec 13, 2010 at 10:41 AM, Edrich de Lange<edd at edd.za.net> wrote:
>>>>
>>>> Oh, Im using chan_ss7 now.
>>>>
>>>> Those channels are up on my side though.(says idle)
>>>>
>>>> Kind regards
>>>>
>>>> On Mon, Dec 13, 2010 at 10:40 AM, Edrich de Lange<edd at edd.za.net> wrote:
>>>>>
>>>>> Ok, its working fine.
>>>>>
>>>>> One problem, for some reason the last 8 cics dont come up on the
>>>>> remote side, and after a while Im getting these errors
>>>>>
>>>>> [Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
>>>>> CIC=59 for unequipped circuit (typ=RSC), link 'l1'.
>>>>> [Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
>>>>> CIC=56 for unequipped circuit (typ=RSC), link 'l1'.
>>>>> [Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
>>>>> CIC=60 for unequipped circuit (typ=RSC), link 'l1'.
>>>>> [Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
>>>>> CIC=62 for unequipped circuit (typ=RSC), link 'l1'.
>>>>> [Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
>>>>> CIC=63 for unequipped circuit (typ=RSC), link 'l1'.
>>>>> [Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
>>>>> CIC=61 for unequipped circuit (typ=RSC), link 'l1'.
>>>>> [Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
>>>>> CIC=58 for unequipped circuit (typ=RSC), link 'l1'.
>>>>> [Dec 13 10:38:54] WARNING[4051]: l4isup.c:4803 l4isup_event: Received
>>>>> CIC=57 for unequipped circuit (typ=RSC), link 'l1'.
>>>>>
>>>>>
>>>>> Kind regards
>>>>>
>>>>> On Sat, Dec 11, 2010 at 8:01 AM, bipin singh<bipinraghuvanshi at gmail.com>
>>>>> wrote:
>>>>>>
>>>>>> Hi
>>>>>> Try it
>>>>>>
>>>>>> adjpointcode=1368
>>>>>> defaultdpc=1368
>>>>>>
>>>>>> and also not set same acp dcp for two links .
>>>>>>
>>>>>> On Fri, Dec 10, 2010 at 11:11 PM, Edrich de Lange<edd at edd.za.net>
>>>>>> wrote:
>>>>>>>
>>>>>>> Good day
>>>>>>>
>>>>>>> I have a setup using a 4 port Digium Card,Asterisk
>>>>>>> 1.6.2.15,libss7-1.0.2,dahdi-linux-complete-2.4.0
>>>>>>>
>>>>>>> My dahdi config looks like so :
>>>>>>>
>>>>>>> # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS/CRC4
>>>>>>> span=2,2,0,ccs,hdb3
>>>>>>> # termtype: te
>>>>>>> bchan=32-46,48-62
>>>>>>> mtp2=47
>>>>>>> #echocanceller=mg2,32-46,48-62
>>>>>>>
>>>>>>> (the other spans are disabled)
>>>>>>>
>>>>>>> [channels]
>>>>>>> signaling=ss7 ;this is ss7 signaling
>>>>>>> ss7type=itu ;using the ITU variant
>>>>>>> ;ss7_called_nai=dynamic ;NAI for outgoing calls
>>>>>>> ;ss7_calling_nai=dynamic ;NAI for incoming calls
>>>>>>> ss7_internationalprefix= ;international prefix value for incoming
>>>>>>> calls
>>>>>>> ss7_nationalprefix= ;national prefix value for incoming
>>>>>>> calls
>>>>>>> ss7_subscriberprefix= ;subscriber prefix value for incoming
>>>>>>> calls
>>>>>>> ss7_unknownprefix= ;unknown prefix value for incoming
>>>>>>> calls
>>>>>>> ss7_explicitacm=yes
>>>>>>> ss7_explictacm=yes
>>>>>>>
>>>>>>> group=1
>>>>>>> context=ss7
>>>>>>> linkset=1
>>>>>>> pointcode=720 ;the point code for this
>>>>>>> system...aka
>>>>>>> SPC
>>>>>>> adjpointcode=1832 ;the point code for the system
>>>>>>> that we are signaling to... aka APC
>>>>>>> defaultdpc=1368 ;the point code for the system
>>>>>>> that the CICs will be negotiated with...aka DPC
>>>>>>> networkindicator=national_spare ;NI value for MTP3
>>>>>>> cicbeginswith=32 ;the starting value of the CICs
>>>>>>> channel=32-46
>>>>>>> cicbeginswith=48
>>>>>>> channel=48-62 ;the channels that are CICs
>>>>>>> sigchan=47 ;the signaling channel
>>>>>>>
>>>>>>> The Links come up. It seems fine.
>>>>>>> When I make a call to the link I get the following on the asterisk CLI
>>>>>>> Unhandled optional parameter 0x8 'Optional forward call indicator'
>>>>>>> [0x0 ]
>>>>>>> Unhandled optional parameter 0x31 'Propagation Delay Counter'
>>>>>>> [0x0 0x5a ]
>>>>>>> Unhandled optional parameter 0x3f 'Location Number'
>>>>>>> [0x84 0x93 0x72 0x38 0x0 0x10 0x7 0x0 0x0 0x0 ]
>>>>>>> Unhandled optional parameter 0x39 'Parameter Compatibility
>>>>>>> Information'
>>>>>>> [0x31 0xd0 0x3f 0xc0 ]
>>>>>>> [Dec 10 19:36:12] WARNING[3627]: chan_dahdi.c:11850 ss7_linkset: IAM
>>>>>>> on unconfigured CIC 6
>>>>>>> [Dec 10 19:36:13] WARNING[3627]: chan_dahdi.c:12142 ss7_linkset: RLC
>>>>>>> on unconfigured CIC 6
>>>>>>>
>>>>>>> It doesnt seem to trigger even the extentions.
>>>>>>>
>>>>>>> I cant get the Chan_ss7 to work, as My DPC and APC are different(if im
>>>>>>> mistaken please assist, I would gladly try chan_ss7)
>>>>>>>
>>>>>>> I just need to get the incoming calls working urgently.
>>>>>>>
>>>>>>> Any assistance will be greatly appreciated.
>>>>>>>
>>>>>>> Kind regards
>>>>>>>
>>>>>>> Edrich de Lange
>>>>>>>
>>>>>>> --
>>>>>>> _____________________________________________________________________
>>>>>>> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>>>>>>>
>>>>>>> asterisk-ss7 mailing list
>>>>>>> To UNSUBSCRIBE or update options visit:
>>>>>>> http://lists.digium.com/mailman/listinfo/asterisk-ss7
>>>>>>
>>>>>>
>>>>>> --
>>>>>> BIPIN RAGHUVANSHI
>>>>>> OPERATION HEAD
>>>>>> ASTERISK (DEVELOPMENT AND RESEARCH)
>>>>>> WWW.EHORIZONS.IN
>>>>>> 011-32323262
>>>>>> 011-46334633
>>>>>>
>>>>>> --
>>>>>> _____________________________________________________________________
>>>>>> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>>>>>>
>>>>>> asterisk-ss7 mailing list
>>>>>> To UNSUBSCRIBE or update options visit:
>>>>>> http://lists.digium.com/mailman/listinfo/asterisk-ss7
>>>>>>
>>
>>
>> --
>> _____________________________________________________________________
>> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>>
>> asterisk-ss7 mailing list
>> To UNSUBSCRIBE or update options visit:
>> http://lists.digium.com/mailman/listinfo/asterisk-ss7
>>
>
More information about the asterisk-ss7
mailing list