[asterisk-ss7] RE : Re: RE : Re: RE : Re: RE : Re: dos TE410P support SS7-ISUP ?

Wed Feb 27 06:43:45 CST 2008

salut darren,

thank you for your help ,Now  all is ok , it was a
probleme in zapata configuration, 

I have just  a worning i don't understand what is :

warning(34 40)  translate.c : 604
_ast_register_translator :plc_samples 160 format f  
????? 

than you very much 

--- "Storer, Darren" <darren.storer at gmail.com> a
écrit :

>  Salut Elkhomeini,
> 
> (it is better to continue in English for the benefit
> of the International
> community...)
> 
> PDP - We are all here to help each other and to
> learn.
> 
> Do the Telco staff have an SS7 analyser (GN Nettest,
> Tekelec, Siemens etc.)
> ? It is time to use an independent device to help
> you see what signals are
> being sent by the Alcatel and the Asterisk switches.
> 
> It is quite common to have some sort of misalignment
> (CICs/signalling
> timeslots/point codes) but sometimes you need to be
> able to see both sides
> of the "conversation" at the same time so you can
> see where the problem is.
> 
> To check that the signalling timeslots are in the
> right place you can use a
> PRI tester (Trend Aurora etc) and you can listen to
> the signalling to
> confirm it is where you expect it to be. When you
> use an audio monitor on
> TS16 the signalling sounds like a buzzing bee. Many
> people forget that TS0
> is for timing and this results in the signalling
> being misplaced by one
> timeslot.
> 
>  Bonne chance!
> 
> Darren
> 
> 
> On 25/02/2008, Elkhomeini <elkhomeini at yahoo.fr>
> wrote:
> >
> > Bonjour,
> > merci beaucoup pour votre aide ,
> >
> >
> > Je crois que mon grand probleme maintenant est :
> la reponse de la question
> > du l'operateur c'est qoui le coc dans mon fichier
> de configuration c'est le
> > linkset ? ?
> >
> > l'operateur il a dit que il peut voir seulment le
> MTP3 layer ( celui qui
> > fait la signalisaion )
> >
> > j'ai fait vos indications
> > mercci de suivais avec moi le probleme
> >
> > *"Storer, Darren" <darren.storer at gmail.com>* a
> écrit :
> >
> > Salut Elkhomeini,
> >
> > Here are a few basic suggestions:
> >
> >  - ask the Telco staff to check that they can see
> layer one from your
> > Asterisk system
> >  - check that your signalling timeslot (usually
> 16) is aligned with the
> > signalling from the Alcatel switch. You can use a
> GN Nettest MPA to auto
> > configure and display the signalling timeslot
> alignment on both systems.
> >  - loop back TX and RX on the first E1 towards the
> Alcatel switch and ask
> > the Telco staff if they can see layer one, then
> ask if layer two starts to
> > align and fails. This will help to prove all the
> cabling/transmission
> > circuits up to the point of interconnect to your
> Asterisk system.
> >
> > Bien amicalement
> >
> > Darren
> >
> > On 24/02/2008, Elkhomeini <elkhomeini at yahoo.fr>
> wrote:
> > >
> > > hi ,
> > >  thank you for your repponse
> > >
> > >
> > > My problem is :
> > >
> > > I have a serveur Lunix red hat with asterisk
> libss7 zaptel 1.4 , I would
> > > like to set with a switche OCB 3.3 alcatel ,
> > > to make test when I make leason betwwen E1 port
> and the switch , the
> > > operators menager dont detect a signal
> > > If a use Zap show status aget E1 ok !!
> > >
> > > My cartd Is TE410P
> > > my poit cod is 2
> > > adj point cod is 4500
> > > linkset =1 ?
> > >
> > > thank you for your help .
> > >
> > >
> > > *"Storer, Darren" <darren.storer at gmail.com>* a
> écrit :
> > >
> > > Hi,
> > >
> > > it is not possible to send you my config files
> as I don't have access to
> > > my SS7 model system; I'm working from a client's
> site at the moment. My
> > > model is using a single E1 Digium card so it
> might be better for you to
> > > request files from another libss7 user.
> > >
> > > In the meantime, have you tried looping back
> your E1 circuits and
> > > observing the SS7 traces by using the "ss7 debug
> linkset" command? In
> > > production SS7 systems we see the circuits
> attempt to align when we loop the
> > > signalling links back; they will fail to come up
> when the point
> > > codes clash...
> > >
> > > HTH
> > >
> > > Darren
> > >
> > > On 22/02/2008, Elkhomeini <elkhomeini at yahoo.fr>
> wrote:
> > > >
> > > > thankyou for your answer ,
> > > > can you sende me exemple of zapata and zaptel
> for asterisk 1.4-r3490echo
> > > >
> > > > I am sure now that my MTP1 is Ok , but may be
> I have a problem In MTP2
> > > > how I can verifed this ?
> > > >
> > > > thankyou
> > > > *"Storer, Darren" <darren.storer at gmail.com>* a
> écrit :
> > > >
> > > > Hi,
> > > >
> > > > E> *dos TE410P  support SS7-ISUP *
> > > >
> > > > Yes, I have used much lower specification
> cards with lib-ss7.
> > > >
> > > > Cheers
> > > >
> > > > Darren
> > > >
> > > >
> > > > On 21/02/2008, Elkhomeini
> <elkhomeini at yahoo.fr> wrote:
> > > > >
> > > > > Hi please Can you help me :
> > > > >
> > > > >
> > > > > *dos TE410P  support SS7-ISUP  ?*
> > > > >
> > > > > *Antoine Megalla <aatef at rocketmail.com>* a
> écrit :
> > > > >
> > > > > Thank you very much Marek,
> > > > >
> > > > > The new chan_ss7-1.0.9 has been working
> flawlessly for
> > > > > the past 18 hours
> > > > > without loosing a single IDLE channel.
> > > > >
> > > > > Thanks again, you made my day,
> > > > >
> > > > > Antoine Megalla.
> > > > >
> > > > > ----- Original Message -----
> > > > > From: "marek cervenka"
> > > > > To:
> > > > > Sent: Wednesday, February 20, 2008 6:16 PM
> > > > > Subject: Re: [asterisk-ss7] "No Idle Circuit
> found"
> > > > > after sometime
> > > > >
> > > > >
> > > > > > On Wed, 20 Feb 2008, Antoine Megalla
> wrote:
> > > > > >
> 
=== message truncated ===>
_______________________________________________
> --Bandwidth and Colocation Provided by
> http://www.api-digital.com--
> 
> asterisk-ss7 mailing list
> To UNSUBSCRIBE or update options visit:
>   
http://lists.digium.com/mailman/listinfo/asterisk-ss7

              OULD MOULAY ELY Elkhomeini 
                      GSM : + 222 7 10 60 87

      _____________________________________________________________________________ 
Ne gardez plus qu'une seule adresse mail ! Copiez vos mails vers Yahoo! Mail http://mail.yahoo.fr