[asterisk-ss7] Starting with SS7. Channel-Configuration

[Tobias Wolf]

Hi,

Vernier Umali schrieb:
> If you do a zrcfg -vvvvv, you would have errors in channels after 48
> since T1 only supports 24 channels per port.
> 
Ok, so if ztcfg shows that 31 channels were configured, as seen below

Zaptel Version: 1.4.5.1
Echo Canceller: MG2
Configuration
======================

SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: D-channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: Clear channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: Clear channel (Default) (Slaves: 24)
Channel 25: Clear channel (Default) (Slaves: 25)
Channel 26: Clear channel (Default) (Slaves: 26)
Channel 27: Clear channel (Default) (Slaves: 27)
Channel 28: Clear channel (Default) (Slaves: 28)
Channel 29: Clear channel (Default) (Slaves: 29)
Channel 30: Clear channel (Default) (Slaves: 30)
Channel 31: Clear channel (Default) (Slaves: 31)

31 channels configured.

When the Jumper on the card are correctly configured for E1, and the
reason for the RED alarm seem to originate of another physical problem
and not in the configuration of the card, right ?

Regards,

-- 

  Tobias Wolf

  Leiter Softwareentwicklung / Kommunikationslösungen

  Evision GmbH



  Wittekindstr. 105

  44139 Dortmund

  Tel: +49 (0)231 - 47790 307

  Fax: +49 (0)231 - 47790 500

  http://www.evision.de



This electronic mail transmission and any accompanying attachments
contain confidential information intended only for the use of the
individual or entity named above. Any dissemination, distribution,
copying or action taken in reliance on the contents of this
communication by anyone other than the intended recipient is strictly
prohibited. If you have received this communication in error
please immediately delete the E-mail and notify the sender at the
above E-mail address. Thank you.
Hövener & Trapp Evision GmbH, Dortmund - HRB Nr.12477, Registergericht
Dortmund - Geschäftsführer Christoph Begall