[asterisk-ss7] how to install Asterisk-ss7 & libss7

[umar tarar]

o o !,  i read the default zapata.conf again (that i had seen only once
before), & found my self how stupid have i been in my prev post, ...so
anyone ignore my prev post plz

On 10/17/06, umar tarar <umar.tarar at gmail.com> wrote:
>
> well yes it was a copy/paste error, but i think i should correct the 2nd
> entry of 'djpointcode=' to 'defaultdpc=' rather than 'adjpointcode=', or if
> i am wrong then plz describe to me what is 'adjpointcode=' for? (by the way,
> tell me about 'adjpointcode=' anyway)
>
> On 10/17/06, Matt Fredrickson <creslin at digium.com> wrote:
> >
> > First of all, it looks like you are either loading chan_zap.so twice, or
> > you have something else that has tried to open the zap channels (maybe
> > chan_ss7.so?).  So you need to get that straightened out.  I would remove
> > the contents of /usr/lib/asterisk/modules and do a make install from your
> > asterisk-trunk directory again.  Second, your lines in your zapata.confthat are supposed to be adjpointcode= look like they are set to djpointcode=
> > instead (Unless that was a copy/paste error).  That would be the reason it
> > is failing at that point.
> >
> > Matthew Fredrickson
> >
> > ----- umar tarar <umar.tarar at gmail.com> wrote:
> > > yes u r right, & i myself had discovered this prob, & i infact posted
> > > two further posts after the one that u(Matt.) responded, but don't
> > > know y did'nt those two posts get on to the asterisk-ss7 lists right
> > > after my previouse post. ok here r those:
> > >
> > > ############post-1############
> > > lately i've discovered that after compiling asterisk-trunk, i dont
> > > have any chan_zap.so file in my /usr/lib/asterisk/modules/, that is y
> > > asterisk while running is unable to load the chan_zap.so & because of
> > > it, it do not do anything about zap, ....am i right?
> > > if yes then what should i do to correctly compile the asterisk-trunk
> > > to get the chan_zap.so (i already have tried make & make install twice
> > > but did'nt get chan_zap.so both times in my
> > > /usr/lib/asterisk/modules/, though chan_zap.c is present in
> > > asterisk-trunk folder)
> > > #############################
> > >
> > > ###########post-2#############
> > > okay Matt.! now some how after fixing that chan_zap.so prob (by
> > > rechecking once again all the three packages), now when i run the
> > > asterisk with forcefully loading the chan_zap.so modules by loading it
> > > into modules.conf , it gives the following error about djpointcode &
> > > sigchan as;
> > >
> > > ------------CLI eror log-----------------
> > > .
> > > .
> > > [ Oct 14 07:28:18 ] NOTICE[4070]: loader.c:793 load_modules: 1 modules
> > > will be loaded.
> > > == Registered application 'ZapSendKeypadFacility'
> > > == Parsing '/etc/asterisk/zapata.conf': Found
> > > [ Oct 14 07:28:18 ] ERROR[4070]: chan_zap.c:11272 linkset_addsigchan:
> > > Unspecified adjpointcode!
> > > .
> > > .
> > > .
> > > res_features.so => (Call Features Resource)
> > > == Parsing '/etc/asterisk/smdi.conf': Found
> > > [ Oct 14 07:28:18 ] WARNING[4070]: res_smdi.c:726 load_module: No SMDI
> > > interfaces are available to listen on, not starting SDMI listener.
> > > [ Oct 14 07:28:18 ] WARNING[4070]: pbx.c:2818
> > > ast_register_application: Already have an application
> > > 'ZapSendKeypadFacility'
> > > == Parsing '/etc/asterisk/zapata.conf': Found
> > > [ Oct 14 07:28:18 ] ERROR[4070]: chan_zap.c:11222 linkset_addsigchan:
> > > Unable to open SS7 sigchan 16 (Device or resource busy)
> > > .
> > > .
> > > .
> > > ----------------------------------------------
> > >
> > > and here r my zapata.conf & zaptel.conf
> > >
> > > -----------------zapata.conf--------------
> > > channels]
> > > context=zapIncoming
> > > switchtype=euroisdn
> > > usecallerid=yes
> > > hidecallerid=no
> > > echocancel=yes
> > > echocancelwhenbridged=yes
> > > musiconhold=default
> > >
> > > signalling = ss7
> > > ss7type = itu
> > >
> > > linkset = 1
> > >
> > > ;pointcode = 0x1680
> > > pointcode = 05760
> > >
> > > ;djpointcode = 0x168a
> > > djpointcode = 05770
> > > ;djpointcode = 05-10-10
> > >
> > > ;defaultdpc = 0x168a
> > > djpointcode = 05770
> > > ;defaultdpc = 05-10-10
> > >
> > > networkindicator=national
> > > cicbeginswith = 1
> > > sigchan = 16 ; First signaling channel
> > > channel=>1-15,17-31
> > >
> > > ;channel=>1-15
> > > ;cicbeginswith=17
> > > ;channel=>17-31
> > > -----------------------------------------------
> > >
> > > ---------------zaptel.conf-----------------
> > > pan=1,1,0,ccs,hdb3
> > > bchan=1-15,17-31
> > > dchan=16
> > > -----------------------------------------------
> > >
> > > now i think the problem is quite identified, so plz suggest me what
> > > should i do to solve this
> > > #############################
> > >
> > > so plz now respond according to having these two posts right after my
> > > previous post (in which i've already mentioned, what the CLI error log
> > > says abt zap --- keep in mind that chan_zap.so did'nt load
> > > autometically rather i forcefully loaded it through 'load' command in
> > > modules.conf)
> > >
> > > waitin for the responces
> > >
> > >
> > >
> > > On 10/14/06 , Matt Fredrickson < creslin at digium.com > wrote: It sounds
> > > like chan_zap.so didn't load... You need to look at what happens when
> > > you load asterisk, to see why chan_zap.so is not loading.
> > >
> > > Matthew Fredrickson
> >
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> >
> > asterisk-ss7 mailing list
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-ss7
> >
>
>
>
> --
>         |__\__/__|   /__/ \__\   |__| \__|
>
>
>


-- 
        |__\__/__|   /__/ \__\   |__| \__|
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-ss7/attachments/20061017/87c0c388/attachment-0001.htm