[asterisk-gui] Hardware setup for channel bank

[Jim Houser]

Thanks for the correction.  
I'm still stuck deep in 1.4 and have not used DAHDI.
Is there a published PDF that can be read to make someone like me aware of the changes and/or enhancements?

Thanks

----- Original Message -----
From: "Ryan Brindley" <rbrindley at digium.com>
To: "Asterisk GUI project discussion" <asterisk-gui at lists.digium.com>
Sent: Tuesday, June 16, 2009 10:50:18 AM GMT -06:00 US/Canada Central
Subject: Re: [asterisk-gui] Hardware setup for channel bank



Marvin, 
I'm not sure the GUI allows breaking up a T1 card into ports, you probably will have to side step the GUI for this one. 

Jim, 
He's using DAHDI, which means he has to edit /etc/dahdi/system.conf and /etc/asterisk/chan_dahdi.conf, instead of the zap files you mentioned :-). 

-- 
Ryan Brindley 
Digium, Inc. | Software Developer 
445 Jan Davis Drive NW - Huntsville, AL 35806 - USA 
main: +1 256-428-6000 fax: +1 256-864-0464 
Check us out at: http://digium.com & http://asterisk.org 

----- Original Message ----- 
From: "Jim Houser" <jhouser at trustamerifirst.com> 
To: "Asterisk GUI project discussion" <asterisk-gui at lists.digium.com> 
Sent: Tuesday, June 16, 2009 10:34:39 AM GMT -06:00 US/Canada Central 
Subject: Re: [asterisk-gui] Hardware setup for channel bank 

I don't know about the Asterisk GUI you are using but I have used the Adit 600 in a bunch of smaller installs for both FXO and FXS connections. Sounds like you need to do some manual editing of the conf files. Make sure you are set for RBS and not PRI then simply setup your zaptel, zapata, and Adit 600 channel signaling as needed. 

The Adit's I have used offer top notch call quality and are rock solid. 



----- Original Message ----- 
From: "marvin horst" <marvin.horst at pbzinc.com> 
To: asterisk-gui at lists.digium.com 
Sent: Tuesday, June 16, 2009 9:40:01 AM GMT -06:00 US/Canada Central 
Subject: [asterisk-gui] Hardware setup for channel bank 


I have a TE122 card which has (1) T1 port that is connected to an Adit 600 channel bank. Channels 1-8 are FXO ports and 9-24 are FXS ports which are connected to internal phone extensions. How do I setup the GUI so the analog ports are available when I configure users? When I use the "Configure Hardware" section of the GUI it detects the card and sets the configuration as a digital trunk, but this won't allow me individual access to the ports for user assignment. 

My testing enviroment is ..... 

asterisk-1.4.25.1 
dahdi -linux-2.1.04 
asterisk-gui-2.0 

I have a working asterisk 1.4 setup in production that is maintained by using the standard conf files, but I'd like to use a GUI if it doesn't turn out to be to restrictive. I'm a little vague on what options are available in the users.conf file and how those settings effect the GUI. 

-- 
Marvin Horst 
Paul B Zimmerman Inc 
(717) 738-7365 x824 

_______________________________________________ 
--Bandwidth and Colocation Provided by http://www.api-digital.com-- 

asterisk-gui mailing list 
To UNSUBSCRIBE or update options visit: 
http://lists.digium.com/mailman/listinfo/asterisk-gui 

_______________________________________________ 
--Bandwidth and Colocation Provided by http://www.api-digital.com-- 

asterisk-gui mailing list 
To UNSUBSCRIBE or update options visit: 
http://lists.digium.com/mailman/listinfo/asterisk-gui 

_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--

asterisk-gui mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-gui