[Asterisk-bsd] 回复： Re: how can i edit the file to make calls!

[Hans Petter Selasky]

Hi,

You need to know which protocol your ISDN line is using. There are some 
variants like point to point and point to multipoint.

When the cable is properly connected it should read something like "F7: 
Connected".

Also you need to do the cabling right.

--HPS

On Friday 11 January 2008, lizhong zhu wrote:
> hello, all of you:
> i changed to Openvox B200P to test it. but i have no luck for that. the
> isdnconfig is  like this: new-host-3# isdnconfig
> controller 8 = {
>   Layer 1:
>     description : HFC-4S PCI ISDN adapter
>     type        : passive ISDN (Basic Rate, 2xB)
>     channels    : 0x3
>     serial      : 0xabd5
>     power_save  : on
>     dialtone    : enabled
>     attached    : yes
>     PH-state    : F4: Awaiting signal
>   Layer 2:
>     driver_type : DRVR_D_CHANNEL
> }
> controller 9 = {
>   Layer 1:
>     description : HFC-4S PCI ISDN adapter
>     type        : passive ISDN (Basic Rate, 2xB)
>     channels    : 0x3
>     serial      : 0xabd6
>     power_save  : on
>     dialtone    : enabled
>     attached    : yes
>     PH-state    : F0: Reset
>   Layer 2:
>     driver_type : DRVR_D_CHANNEL
> }
> controller 10 = {
>   Layer 1:
>     description : HFC-4S PCI ISDN adapter
>     type        : passive ISDN (Basic Rate, 2xB)
>     channels    : 0x3
>     serial      : 0xabd7
>     power_save  : on
>     dialtone    : enabled
>     attached    : yes
>     PH-state    : F0: Reset
>   Layer 2:
>     driver_type : DRVR_D_CHANNEL
> }
> controller 11 = {
>   Layer 1:
>     description : HFC-4S PCI ISDN adapter
>     type        : passive ISDN (Basic Rate, 2xB)
>     channels    : 0x3
>     serial      : 0xabd8
>     power_save  : on
>     dialtone    : enabled
>     attached    : yes
>     PH-state    : F0: Reset
>   Layer 2:
>     driver_type : DRVR_D_CHANNEL
> }
> new-host-3#
> i also test by run: capitest -u 8 -o 1357XXXXXX.
> main.c: capi_send_listen_request: sending listen request for incoming_calls
> main.c: capi_send_listen_request: sending listen request for incoming_calls
> main.c: capi_send_listen_request: sending listen request for incoming_calls
> dialing out, 1 / 1 ...
> main.c: cd_event: disconnected: user busy
> i do not know what happen with the card. Could you tell me a right command
> for isdnconfig for BRI 200P for TE mode? i just want to set all TE mode to
> test it first. asterisk can start with capi. cable is ok. i do not know why
> i can not make calls. regards,
> zhu
>
> Hans Petter Selasky <hselasky at c2i.net> 写道： On Thursday 10 January 2008, 
lizhong zhu wrote:
> > hello, all of friends:
> > thanks, Richard Neese. i edit the kernel and add what you gave me and
> > recompile kernel, the isdn and capi seems work. i run isdnconfig it show
> > s four contralloer. my card is OpenVox B400P. now asterisk can start and
> > show
> >
> > : new-host-3*CLI> capi show channels
> >
> > CAPI thread [0x0] {
> >  Application ID     : 0x00000000
> >  Application uptime : 0x00000945 seconds
> >
> >  Call descriptor statistics:
> >     allocation count        : 0x00000000 call descriptors
> >     free count              : 0x00000000 call descriptors
> >     in memory count         : 0x00000000 call descriptors
> >     in use count            : 0x00000000 call descriptors
> >     record allocation rate  :     0x0000 calls/second
> >     limit allocation rate   :     0x0010 calls/second
> >  Currently active calls:
> >     channel name, source->destination, call ID, in/out
> > }
> > Config entry 'ISDN2' {
> >  b_channels_curr : 2 call descriptor(s) free
> >  b_channels_max  : 2 call descriptor(s) total
> > }
> > Config entry 'ISDN1' {
> >  b_channels_curr : 2 call descriptor(s) free
> >  b_channels_max  : 2 call descriptor(s) total
> > }
> >
> > new-host-3*CLI>
> > i have no idea for capi.conf for BRI. the LEDs are not blink. i would set
> > all 4 ports are in TE mode. anyone can tell me some setting for how to
> > start isdn4bsd and as capi.conf ? thanks!
> > zhu
>
> Hi,
>
> You set the mode using "isdnconfig". What does "isdnconfig" output? The
> leds are currently not supported.
>
> You make make testcalls using "capitest".
>
> --HPS
>
>
>
> ---------------------------------
> 雅虎邮箱传递新年祝福，个性贺卡送亲朋！