[Asterisk-bsd] TDM400p results so far and a question.

[Chris Stenton]

In your zapata.conf you have

context=internal

should this be context=from-analog

You will not see anything on the console unless it hits a valid extention in 
the selected context.

Chris

----- Original Message ----- 
From: "Jeff Rizzo" <riz+asterisk at boogers.sf.ca.us>
To: "Asterisk on BSD discussion" <asterisk-bsd at lists.digium.com>
Sent: Sunday, October 17, 2004 7:23 PM
Subject: [Asterisk-bsd] TDM400p results so far and a question.


> I'm using the FreeBSD zaptel driver under FreeBSD 5.2.1-release (not sure 
> how to tell what version of the zaptel driver - but I got it in email in 
> the last three weeks.  :) with a TDM400p card which has one FXS and one 
> FXO port.  Things are working pretty well in the tests so far, and I can 
> now confirm that the FXS port _does_ work pretty well.
>
> I'm running the following version of Asterisk:
>
> Asterisk CVS-HEAD-10/16/04-15:57:30 built by riz at fb.boogers.sf.ca.us on a 
> i386 running FreeBSD
>
> Here's what I've seen so far - since I'm pretty new to asterisk and have 
> never (!) run it under Linux, perhaps someone can let me know if I'm doing 
> anything wrong.
>
> My zapata.conf is thus:
>
> [channels]
> language=en
> context=internal
> usecallerid=yes
> echocancel=yes
> echocancelwhenbridged=yes
> signalling=fxo_ks
> channel => 1
> context=from-analog
> signalling=fxs_ks
> rxgain=10.5
> txgain=0
> callprogress=yes
> channel => 2
>
>
> I've got an analog rotary-dial phone (yes, really) hooked up to the FXS 
> port, and I'm able to dial other extensions with it just fine, and cause 
> it to ring when its extension is dialed.  When I plug in a touchtone 
> phone, I have intermittent trouble getting * to recognize the digits 
> dialed.  I haven't yet had time to characterize the trouble, but my guess 
> is I just need to tweak some settings.  The only other thing I've noticed 
> is that the dialtone sounds a little wonky - almost like static on the 
> line, a steady clicking sound.  For all I know, this may be normal, 
> though.  :)
>
> On the FXO port, I am able to successfully dial out without issue, but I 
> can't seem to get asterisk to answer an incoming call on the line... I'm 
> almost certain this is a configuration problem, but I'm at a loss what to 
> do next.  I don't see _anything_ on the console when an incoming call is 
> ringing, even though I've got verbose set to 9... should I see anything? 
> Here's the 'from-analog' context in my extensions.conf:
>
> [from-analog]
> exten => s,1,Dial(SIP/3000&Zap/1)
>
>
> ... which I would expect to ring both SIP/3000 (which works) and Zap/1, 
> the analog phone (which also works in other contexts).  But as I've said, 
> I see no indication that asterisk even notices the line ringing.
> All in all I'm quite pleased with the state of affairs thus far.  Any 
> troubleshooting suggestions would be most welcome.
> Thanks,
> +j
>
>
>
>
> _______________________________________________
> Asterisk-BSD mailing list
> Asterisk-BSD at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-bsd
>