Hi everyone,<div><br></div><div>I am reading through Sangoma Wiki right now. But someone may already and quickly notice this. I have a system that is down since the morning (maybe power intruptions). All seems fine except for "wanrouter status" shows disconnected. Following are the alarms raised. Should I call telco (they have long wait times) or should I just keep searching online for troubleshooting tips. "<b>wanpipe1 | AFT TE1 | N/A | Disconnected |" <<<<<</b> This is what shows.</div>
<div><br></div><div><br></div><div><br></div><div><div>root@pbx:~ $ wanpipemon -i w1g1 -c Ta</div><div><br></div><div>***** w1g1: T1 Rx Alarms (Framer) *****</div><div><br></div><div><b>ALOS: OFF | LOS: ON</b></div>
<div><b>RED: ON | AIS: OFF</b></div><div><b>LOF: ON | RAI: OFF</b></div><div><b><br></b></div><div><b>***** w1g1: T1 Rx Alarms (LIU) *****</b></div><div><b><br></b></div><div><b>Short Circuit: OFF</b></div>
<div><b>Open Circuit: OFF</b></div><div><b>Loss of Signal: ON</b></div><div><br></div><div>***** w1g1: T1 Tx Alarms *****</div><div><br></div><div>AIS: ON | YEL: ON</div><div><br></div><div><br></div><div>***** w1g1: T1 Performance Monitoring Counters *****</div>
<div><br></div><div>Line Code Violation : 0</div><div>Bit Errors (CRC6/Ft/Fs) : 0</div><div>Out of Frame Errors : 0</div><div><br></div><div><br></div><div>Rx Level : < -36db</div><div><br></div><div><br>
</div><div>root@pbx:~ $ ifconfig</div><div>w1g1 Link encap:Point-to-Point Protocol </div><div> UP POINTOPOINT NOARP MTU:8 Metric:1</div><div> RX packets:0 errors:0 dropped:0 overruns:0 frame:0</div>
<div> TX packets:0 errors:0 dropped:0 overruns:0 carrier:4383</div><div> collisions:0 txqueuelen:100 </div><div> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)</div><div> Interrupt:177 Memory:f8c50000-f8c51fff </div>
<div><br></div><div>root@pbx:~ $ wanrouter hwprobe verbose</div><div><br></div><div>-----------------------------------------</div><div>| Wanpipe Hardware Probe Info (verbose) |</div><div>-----------------------------------------</div>
<div>1 . AFT-A101-SH : SLOT=4 : BUS=4 : IRQ=9 : CPU=A : PORT=1 : HWEC=32 : V=36</div><div>+01:DS26521: PCIe: PLX2</div><div><br></div><div>Card Cnt: A101-2=1 </div><div><br></div><div>root@pbx:~ $ wanrouter status</div><div>
<br></div><div>Devices currently active:</div><div> wanpipe1</div><div><br></div><div><br></div><div>Wanpipe Config:</div><div><br></div><div>Device name | Protocol Map | Adapter | IRQ | Slot/IO | If's | CLK | Baud rate |</div>
<div>wanpipe1 | N/A | A101/1D/A102/2D/4/4D/8| 177 | 4 | 1 | N/A | 0 |</div><div><br></div><div>Wanrouter Status:</div><div><br></div><div>Device name | Protocol | Station | Status |</div>
<div><b>wanpipe1 | AFT TE1 | N/A | Disconnected |</b></div><div><br></div><div><br></div><div><b>pbx*CLI> pri show span 1</b></div><div>Primary D-channel: 24</div><div>Status: Provisioned, In Alarm, Down, Active</div>
<div>Switchtype: National ISDN</div><div>Type: CPE</div><div>Window Length: 0/7</div><div>Sentrej: 0</div><div>SolicitFbit: 0</div><div>Retrans: 0</div><div>Busy: 0</div><div>Overlap Dial: 0</div><div>Logical Channel Mapping: 0</div>
<div>T200 Timer: 1000</div><div>T203 Timer: 10000</div><div>T305 Timer: 30000</div><div>T308 Timer: 4000</div><div>T309 Timer: -1</div><div>T313 Timer: 4000</div><div>N200 Counter: 3</div></div><div><br></div><div><br></div>
<div><br></div><div><br></div><div>Thanks,</div>