Hello,
<br>
<br>We are having issues with a NEW Sangoma A108D:
<br>
<br>    -- Executing [691918892@pbx1:1] Dial(&quot;SIP/xtravoip200-009d24b0&quot;, 
&quot;DAHDI/g0/691918892|30|m&quot;) in new stack
<br>[Oct  1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No 
translator path exists for channel type DAHDI (native 76) to 256
<br>[Oct  1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable 
to create channel of type &#39;DAHDI&#39; (cause 58 - Bearer capability not 
available)
<br>  == Everyone is busy/congested at this time (1:0/0/1)
<br>    -- Executing [691918892@pbx1:2] Hangup(&quot;SIP/xtravoip200-009d24b0&quot;, 
&quot;&quot;) in new stack
<br>  == Spawn extension (pbx1, 691918892, 2) exited non-zero on 
&#39;SIP/xtravoip200-009d24b0&#39;
<br>
<br>wanrouter status:
<br>
<br>wanrouter status
<br>
<br>Devices currently active:
<br>    wanpipe1 wanpipe2 wanpipe3 wanpipe4 wanpipe5 wanpipe6 wanpipe7 wanpipe8
<br>
<br>
<br>Wanpipe Config:
<br>
<br>Device name | Protocol Map | Adapter  | IRQ | Slot/IO | If&#39;s | CLK | 
Baud rate |
<br>wanpipe1    | N/A          | A101/1D/A102/2D/4/4D/8| 17  | 4       | 
1    | N/A | 0         |
<br>wanpipe2    | N/A          | A101/1D/A102/2D/4/4D/8| 17  | 4       | 
1    | N/A | 0         |
<br>wanpipe3    | N/A          | A101/1D/A102/2D/4/4D/8| 17  | 4       | 
1    | N/A | 0         |
<br>wanpipe4    | N/A          | A101/1D/A102/2D/4/4D/8| 17  | 4       | 
1    | N/A | 0         |
<br>wanpipe5    | N/A          | A101/1D/A102/2D/4/4D/8| 17  | 4       | 
1    | N/A | 0         |
<br>wanpipe6    | N/A          | A101/1D/A102/2D/4/4D/8| 17  | 4       | 
1    | N/A | 0         |
<br>wanpipe7    | N/A          | A101/1D/A102/2D/4/4D/8| 17  | 4       | 
1    | N/A | 0         |
<br>wanpipe8    | N/A          | A101/1D/A102/2D/4/4D/8| 17  | 4       | 
1    | N/A | 0         |
<br>
<br>Wanrouter Status:
<br>
<br>Device name | Protocol | Station | Status        |
<br>wanpipe1    | AFT TE1  | N/A     | Connected     |
<br>wanpipe2    | AFT TE1  | N/A     | Disconnected  |
<br>wanpipe3    | AFT TE1  | N/A     | Disconnected  |
<br>wanpipe4    | AFT TE1  | N/A     | Disconnected  |
<br>wanpipe5    | AFT TE1  | N/A     | Disconnected  |
<br>wanpipe6    | AFT TE1  | N/A     | Disconnected  |
<br>wanpipe7    | AFT TE1  | N/A     | Disconnected  |
<br>wanpipe8    | AFT TE1  | N/A     | Disconnected  |
<br>
<br>root@Sangoma-Testing:/etc/asterisk# wanpipemon -i w1g1 -c Ta
<br>
<br>***** w1g1: E1 Alarms (Framer) *****
<br>
<br>ALOS:    OFF    | LOS:    OFF
<br>RED:    OFF    | AIS:    OFF
<br>OOF:    OFF    | RAI:    OFF
<br>
<br>***** w1g1: E1 Alarms (LIU) *****
<br>
<br>Short Circuit:    OFF
<br>Open Circuit:    OFF
<br>Loss of Signal:    OFF
<br>
<br>
<br>***** w1g1: E1 Performance Monitoring Counters *****
<br>
<br>Line Code Violation    : 187
<br>Far End Block Errors    : 0
<br>CRC4 Errors        : 0
<br>FAS Errors        : 0
<br>
<br>
<br>Rx Level    : &gt; -2.5db
<br>
<br>
<br>root@Sangoma-Testing:/etc/asterisk# asterisk -rx &#39;pri show spans&#39;
<br>PRI span 1/0: Provisioned, Up, Active
<br>PRI span 2/0: Provisioned, In Alarm, Down, Active
<br>PRI span 3/0: Provisioned, In Alarm, Down, Active
<br>PRI span 4/0: Provisioned, In Alarm, Down, Active
<br>PRI span 5/0: Provisioned, In Alarm, Down, Active
<br>PRI span 6/0: Provisioned, In Alarm, Down, Active
<br>PRI span 7/0: Provisioned, In Alarm, Down, Active
<br>PRI span 8/0: Provisioned, In Alarm, Down, Active
<br>
<br>What&#39;s happening?
<br>
<br>Hope you can help me
<br>
<br>Regards!