<br><br><div class="gmail_quote">On Wed, Jul 1, 2009 at 10:49 AM, Marco Signorini <span dir="ltr"><<a href="mailto:marcotasto@libero.it">marcotasto@libero.it</a>></span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<div bgcolor="#ffffff" text="#000000"><div><div></div><div class="h5">
Tom O'Connor wrote:
<blockquote cite="http://mida54141a60907010209y2bb04acan2a2495bbfbb7caca@mail.gmail.com" type="cite"><br>
<br>
<div class="gmail_quote">On Wed, Jul 1, 2009 at 7:37 AM, Francesco
Peeters <span dir="ltr"><<a href="mailto:francesco@fampeeters.com" target="_blank">francesco@fampeeters.com</a>></span>
wrote:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<div>John F. Ervin wrote:<br>
> What do you do if you find things sharing interrupts (IRQ 11) in my<br>
> case with my X100P card. I believe there is some sort of internal<br>
> audio card in my cheap slow PC.<br>
><br>
</div>
Check the BIOS whether you can:<br>
Change the IRQ assignments<br>
Disable the extra hardware using the same IRQ<br>
<br>
Or otherwise try changing the slot it is in... I had very good results<br>
in the past swapping card around<br>
<br>
Good luck!<br>
<font color="#888888"><br>
</font></blockquote>
</div>
<br>
I did a bit of investigation WRT the IRQ settings on this box. <br>
<br>
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev
a3) (prog-if 20)<br>
Subsystem: Hewlett-Packard Company Device 3207<br>
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 11<br>
--<br>
01:05.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2
MX/MX 400] (rev b2)<br>
Subsystem: Hewlett-Packard Company Device 3207<br>
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11<br>
--<br>
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721
Gigabit Ethernet PCI Express (rev 11)<br>
Subsystem: Hewlett-Packard Company Device 3209<br>
Flags: bus master, fast devsel, latency 0, IRQ 11<br>
--<br>
81:01.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN
interface<br>
Subsystem: Device 79fe:0001<br>
Flags: bus master, medium devsel, latency 64, IRQ 11<br>
<br>
So basically there's 2 network cards and a USB controller sharing IRQ
11 with the Openvox card. <br>
<br>
I wasn't able to find any settings in the bios to manually configure
IRQ assignments :( <br>
<br>
Could someone tell me how to set which IRQ the ISDN card picks up?<br>
<br>
-- <br>
Tom O'Connor<br>
<br>
<a href="http://www.twinhelix.org" target="_blank">http://www.twinhelix.org</a><br>
<a href="mailto:tom@twinhelix.org" target="_blank">tom@twinhelix.org</a><br>
</blockquote></div></div>
Hi, <br>
Unfortunately is not always possible and it depends on how the
mainboard was realized. For what I can understand a lot of producers
decide to route only a subset of physical IRQ lines to the PCI slots (I
think is something related to cost reduction) and to share it with
other onboard peripherals. <br>
This lets impossible to change the IRQ assignment for expansion cards.<br>
<br>
This is not always true and sometimes swapping add-on cards solves the
problem.<br>
<br>
We had better results with cards based on new Digium technology or with
Sangoma cards.<br>
<br>
</div></blockquote></div>There is almost no room for manouvering in the HP bios. There's no ability to disable stuff like parallel ports, or anything else really. <br><br>I don't think i'd buy digium hardware again. I'm already considering RMAing these cards and getting Sangoma ones. <br>
<br clear="all"><br>-- <br>Tom O'Connor<br><br><a href="http://www.twinhelix.org">http://www.twinhelix.org</a><br><a href="mailto:tom@twinhelix.org">tom@twinhelix.org</a><br>