<table cellspacing="0" cellpadding="0" border="0" ><tr><td valign="top" style="font: inherit;">This an FXO card, but for some reason it is configured as an FXS card on asterisk....as per asterisk install Guide...<br><br>--- On <b>Tue, 8/26/08, Eric "ManxPower" Wieling <i><eric@fnords.org></i></b> wrote:<br><blockquote style="border-left: 2px solid rgb(16, 16, 255); margin-left: 5px; padding-left: 5px;">From: Eric "ManxPower" Wieling <eric@fnords.org><br>Subject: Re: [asterisk-users] X100P Card in OFFHOOK state<br>To: jonty_11@yahoo.com, "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com><br>Date: Tuesday, August 26, 2008, 11:22 PM<br><br><pre>It would be clearer if it said "Hookstate (FXS ports only): Offhook"<br><br>i.e. the state information is not valid for FXO ports.<br><br>Jay Ray wrote:<br>> Any pointers on this one?<br>> <br>> --- On Tue, 8/26/08, Jay Ray <jonty_11@yahoo.com>
wrote:<br>> From: Jay Ray <jonty_11@yahoo.com><br>> Subject: [asterisk-users] X100P Card in OFFHOOK state<br>> To: asterisk-users@lists.digium.com<br>> Date: Tuesday, August 26, 2008, 12:24 PM<br>> <br>> After I make a call o n the Zaptel Card X100P FXO module....it remains<br>offhook state as shown here...<br>> <br>> Signalling Type: FXS Kewlstart<br>> Radio: 0re2uk*CLI><br>> Owner: <None>*CLI><br>> Real: <None>k*CLI><br>> Callwait: <None>I><br>> Threeway: <None>I><br>> Confno: -12uk*CLI><br>> Propagated Conference: -1<br>> Real in conference: 0<br>> DSP: noore2uk*CLI><br>> Relax DTMF: noCLI><br>> Dialing/CallwaitCAS: 0/0<br>> Default law: ulaw><br>> Fax Handled: noLI><br>> Pulse phone: noLI><br>> Echo Cancellation: 128 taps, currently OFF<br>> Actual Confinfo: Num/0, Mode/0x0000<br>> Actual Confmute: No<br>>
Hookstate (FXS only): Offhook<br>> <br>> <br>> <br>> ------------------<br>> Sometimes it still takes a new call while in this state and sometimes<br>rejects it...<br>> How to correct it such that after I hangup a call it goes back to onhook<br>> state...<br>> <br>> reloading wcfxo module using modprobe clears the issue....<br>> <br>> <br>> <br>> <br>> <br>> _______________________________________________<br>> -- Bandwidth and Colocation Provided by http://www.api-digital.com --<br>> <br>> AstriCon 2008 - September 22 - 25 Phoenix, Arizona<br>> Register Now: http://www.astricon.net<br>> <br>> asterisk-users mailing list<br>> To UNSUBSCRIBE or update options visit:<br>> http://lists.digium.com/mailman/listinfo/asterisk-users<br>> <br>> <br>> <br>> <br>> <br>> ------------------------------------------------------------------------<br>> <br>>
_______________________________________________<br>> -- Bandwidth and Colocation Provided by http://www.api-digital.com --<br>> <br>> AstriCon 2008 - September 22 - 25 Phoenix, Arizona<br>> Register Now: http://www.astricon.net<br>> <br>> asterisk-users mailing list<br>> To UNSUBSCRIBE or update options visit:<br>> http://lists.digium.com/mailman/listinfo/asterisk-users<br>> <br><br>-- <br>Consulting for Asterisk, Polycom, Sangoma, Digium, Cisco, LAN, WAN, QoS, <br>T-1, PRI, Frame Relay, Linux, and network design. Based near <br>Birmingham, AL. Now accepting clients worldwide.<br></pre></blockquote></td></tr></table><br>