<table cellspacing="0" cellpadding="0" border="0" ><tr><td valign="top" style="font: inherit;">1.4 from CVS..<br><br> Last nite...I corrected the below error by change the check in Makefile for HOTPLUG="yes to a "no" and it does not try to download and install that tar.gz file anymore..Not sure if it will cause a prob..<br><br>Later all teh install steps worked fine until I ran ztcfg which errored with - unable to open devide.." I found that /dev/zap did not exist...now a little more searching revealed that my devices for zap wer einstalledin /udev..i justl inked those to .dev.zap and ztcfg worked....looks like my card is up and running..<br><br>Can I Just connect my homephone line to the LINE port of the X100P card and use a softphone to outpulse calls over that Line??<br><br>--- On <b>Wed, 8/13/08, Paul Hales <i><pdhales@optusnet.com.au></i></b> wrote:<br><blockquote style="border-left: 2px solid rgb(16, 16, 255); margin-left: 5px;
padding-left: 5px;">From: Paul Hales <pdhales@optusnet.com.au><br>Subject: Re: [asterisk-users] FC2 and Zaptel<br>To: jonty_11@yahoo.com, "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com><br>Date: Wednesday, August 13, 2008, 12:26 AM<br><br><pre>Which versions of Zaptel have you tried to build?<br><br>PaulH<br><br><br>Jay Ray wrote:<br>> Any ideas, please they are highly appreciated....<br>><br>> --- On *Mon, 8/4/08, Jay Ray /<jonty_11@yahoo.com>/* wrote:<br>><br>> From: Jay Ray <jonty_11@yahoo.com><br>> Subject: [asterisk-users] FC2 and Zaptel<br>> To: asterisk-users@lists.digium.com<br>> Date: Monday, August 4, 2008, 12:02 AM<br>><br>> Hi,<br>><br>> I am using an older Fedora - FC2 and trying to install<br>> zaptel.(for X100P card I have - FXO with one line port and one<br>> Phone port)<br>><br>> Fist I
tried installin from RPM...as given here (also tried<br>> installing Zapata)<br>> http://www.voip-info.org/wiki/view/Asterisk+Linux+Fedora (FC2 is<br>> at the end)<br>><br>> But looks like zaptel executable was not there...same for zapata...<br>><br>> Then I started on downloading the source, I successfully completed<br>> MAKE for zaptel...but make install has following error...Full o/p<br>> follows:<br>> =========================================================<br>> [root@fedoracore2uk zaptel]# make install<br>> make[1]: Entering directory `/usr/src/zaptel'<br>> make -C /lib/modules/2.6.10-1.771_FC2/build ARCH=i386<br>> SUBDIRS=/usr/src/zaptel/kernel HOTPLUG_FIRMWARE=yes<br>> KBUILD_OBJ_M="pciradio.o tor2.o torisa.o wcfxo.o wct1xxp.o<br>wctdm.o<br>> wcte11xp.o wcusb.o zaptel.o ztd-eth.o ztd-loc.o ztdummy.o<br>> ztdynamic.o zttranscode.o
wct4xxp/ wctc4xxp/ xpp/ wctdm24xxp/<br>> wcte12xp/" modules<br>> make[2]: Entering directory `/lib/modules/2.6.10-1.771_FC2/build'<br>><br>> Building modules, stage 2.<br>> MODPOST<br>> *** Warning: "class_device_destroy"<br>> [/usr/src/zaptel/kernel/zaptel.ko] undefined!<br>> make[2]: Leaving directory `/lib/modules/2.6.10-1.771_FC2/build'<br>> make[2]: Entering directory `/usr/src/zaptel/kernel/xpp/utils'<br>> make[2]: Nothing to be done for `all'.<br>> make[2]: Leaving directory `/usr/src/zaptel/kernel/xpp/utils'<br>> make[1]: Leaving directory `/usr/src/zaptel'<br>> install -d /etc/udev/rules.d<br>> build_tools/genudevrules > /etc/udev/rules.d/zaptel.rules<br>> build_tools/uninstall-modules dahdi 2.6.10-1.771_FC2<br>> make -C /lib/modules/2.6.10-1.771_FC2/build ARCH=i386<br>> SUBDIRS=/usr/src/zaptel/kernel
HOTPLUG_FIRMWARE=yes<br>> KBUILD_OBJ_M="pciradio.o tor2.o torisa.o wcfxo.o wct1xxp.o<br>wctdm.o<br>> wcte11xp.o wcusb.o zaptel.o ztd-eth.o ztd-loc.o ztdummy.o<br>> ztdynamic.o zttranscode.o wct4xxp/ wctc4xxp/ xpp/ wctdm24xxp/<br>> wcte12xp/" INSTALL_MOD_PATH= INSTALL_MOD_DIR=misc modules_install<br>> make[1]: Entering directory `/lib/modules/2.6.10-1.771_FC2/build'<br>> INSTALL /usr/src/zaptel/kernel/pciradio.ko<br>> INSTALL /usr/src/zaptel/kernel/tor2.ko<br>> INSTALL /usr/src/zaptel/kernel/torisa.ko<br>> INSTALL /usr/src/zaptel/kernel/wcfxo.ko<br>> INSTALL /usr/src/zaptel/kernel/wct1xxp.ko<br>> INSTALL /usr/src/zaptel/kernel/wct4xxp/wct4xxp.ko<br>> INSTALL /usr/src/zaptel/kernel/wctc4xxp/wctc4xxp.ko<br>> INSTALL /usr/src/zaptel/kernel/wctdm.ko<br>> INSTALL /usr/src/zaptel/kernel/wctdm24xxp/wctdm24xxp.ko<br>> INSTALL
/usr/src/zaptel/kernel/wcte11xp.ko<br>> INSTALL /usr/src/zaptel/kernel/wcte12xp/wcte12xp.ko<br>> INSTALL /usr/src/zaptel/kernel/wcusb.ko<br>> INSTALL /usr/src/zaptel/kernel/xpp/xpd_fxo.ko<br>> INSTALL /usr/src/zaptel/kernel/xpp/xpd_fxs.ko<br>> INSTALL /usr/src/zaptel/kernel/xpp/xpd_pri.ko<br>> INSTALL /usr/src/zaptel/kernel/xpp/xpp.ko<br>> INSTALL /usr/src/zaptel/kernel/xpp/xpp_usb.ko<br>> INSTALL /usr/src/zaptel/kernel/zaptel.ko<br>> INSTALL /usr/src/zaptel/kernel/ztd-eth.ko<br>> INSTALL /usr/src/zaptel/kernel/ztd-loc.ko<br>> INSTALL /usr/src/zaptel/kernel/ztdummy.ko<br>> INSTALL /usr/src/zaptel/kernel/ztdynamic.ko<br>> INSTALL /usr/src/zaptel/kernel/zttranscode.ko<br>> make[1]: Leaving directory `/lib/modules/2.6.10-1.771_FC2/build'<br>> [ `id -u` = 0 ] && /sbin/depmod -a 2.6.10-1.771_FC2 || :<br>> make[1]:
Entering directory `/usr/src/zaptel/kernel/xpp/utils'<br>> make[1]: Nothing to be done for `all'.<br>> make[1]: Leaving directory `/usr/src/zaptel/kernel/xpp/utils'<br>> make[1]: Entering directory `/usr/src/zaptel/kernel/xpp/utils'<br>> install -d /usr/sbin<br>> install genzaptelconf fpga_load zt_registration xpp_sync lszaptel<br>> xpp_blink zapconf zaptel_hardware /usr/sbin/<br>> install -d /usr/share/zaptel<br>> install -m 644 ../firmwares/FPGA_1141.hex<br>> ../firmwares/FPGA_1151.hex ../firmwares/FPGA_FXS.hex<br>> ../firmwares/USB_FW.hex init_fxo_modes /usr/share/zaptel/<br>> install ../init_card_1_30 ../init_card_2_30 ../init_card_3_30<br>> ../init_card_4_30 xpp_fxloader /usr/share/zaptel/<br>> install -d /usr/share/man/man8<br>> install -m 644 genzaptelconf.8 fpga_load.8 zt_registration.8<br>> xpp_sync.8 lszaptel.8 xpp_blink.8 zapconf.8
zaptel_hardware.8<br>> /usr/share/man/man8/<br>> install -d /etc/hotplug/usb<br>> install -m 644 xpp_fxloader.usermap /etc/hotplug/usb/<br>> # for backward compatibility and for hotplug users:<br>> ln -sf /usr/share/zaptel/xpp_fxloader /etc/hotplug/usb/<br>> install -d /etc/udev/rules.d<br>> install -m 644 xpp.rules /etc/udev/rules.d/<br>> install -d /usr/lib/perl5/site_perl/5.8.3<br>> for i in Zaptel Zaptel/Xpp Zaptel/Config Zaptel/Hardware; \<br>> do \<br>> install -d "/usr/lib/perl5/site_perl/5.8.3/$i";<br>\<br>> done<br>> for i in Zaptel.pm Zaptel/Chans.pm Zaptel/Hardware.pm<br>> Zaptel/Span.pm Zaptel/Utils.pm Zaptel/Xpp.pm Zaptel/Xpp/Line.pm<br>> Zaptel/Xpp/Xbus.pm Zaptel/Xpp/Xpd.pm Zaptel/Config/Defaults.pm<br>> Zaptel/Hardware/PCI.pm Zaptel/Hardware/USB.pm; \<br>> do \<br>> install -m 644 "zconf/$i"<br>>
"/usr/lib/perl5/site_perl/5.8.3/$i"; \<br>> done<br>> make[1]: Leaving directory `/usr/src/zaptel/kernel/xpp/utils'<br>> install -d /sbin<br>> install fxotune ztcfg ztmonitor ztspeed zttest ztscan zttool /sbin/<br>> install -d /usr/share/man/man8<br>> install -m 644 doc/fxotune.8 doc/ztcfg.8 doc/ztmonitor.8<br>> doc/ztspeed.8 doc/zttest.8 doc/ztscan.8 doc/zttool.8<br>> /usr/share/man/man8/<br>> /usr/bin/install -c -D -m 755 libtonezone.a /usr/lib/libtonezone.a<br>> /usr/bin/install -c -D -m 755 libtonezone.so<br>> /usr/lib/libtonezone.so.1.0<br>> if [ `id -u` = 0 ]; then \<br>> /sbin/ldconfig || : ;\<br>> fi<br>> rm -f /usr/liblibtonezone.so<br>> /bin/ln -sf libtonezone.so.1.0 \<br>> /usr/lib/libtonezone.so.1<br>> /bin/ln -sf libtonezone.so.1.0 \<br>> /usr/lib/libtonezone.so<br>>
/sbin/restorecon -v /usr/lib/libtonezone.so<br>> /usr/bin/install -c -D -m 644 kernel/zaptel.h<br>> /usr/include/zaptel/zaptel.h<br>> /usr/bin/install -c -D -m 644 tonezone.h<br>> /usr/include/zaptel/tonezone.h<br>> make -C firmware hotplug-install DESTDIR= HOTPLUG_FIRMWARE=yes<br>> make[1]: Entering directory `/usr/src/zaptel/firmware'<br>> make[1]: *** No rule to make target<br>> `zaptel-fw-oct6114-128-1.05.01.tar.gz', needed by<br>> `hotplug-install'. Stop.<br>> make[1]: Leaving directory `/usr/src/zaptel/firmware'<br>> make: *** [install-firmware] Error 2<br>> You have new mail in /var/spool/mail/root<br>> ==============================================================<br>><br>> Any ideas would be appreciated on how to fix this....<br>><br>> Thx,<br>> Jay<br>><br>><br>>
_______________________________________________<br>> -- Bandwidth and Colocation Provided by http://www.api-digital.com --<br>><br>> AstriCon 2008 - September 22 - 25 Phoenix, Arizona<br>> Register Now: http://www.astricon.net<br>><br>> asterisk-users mailing list<br>> To UNSUBSCRIBE or update options visit:<br>> http://lists.digium.com/mailman/listinfo/asterisk-users<br>><br>><br>> ------------------------------------------------------------------------<br>><br>> _______________________________________________<br>> -- Bandwidth and Colocation Provided by http://www.api-digital.com --<br>><br>> AstriCon 2008 - September 22 - 25 Phoenix, Arizona<br>> Register Now: http://www.astricon.net<br>><br>> asterisk-users mailing list<br>> To UNSUBSCRIBE or update options visit:<br>>
http://lists.digium.com/mailman/listinfo/asterisk-users<br><br></pre></blockquote></td></tr></table><br>