<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type">
<title></title>
</head>
<body bgcolor="#ffffff" text="#000000">
Hello Moises. I enabled debug mode in asterisk. When I dial, I get:<br>
<br>
<small><i><small>Jul 19 14:24:38 DEBUG[4463]: build_route: Contact hop:
<sip:192.168.0.6:5060><br>
Jul 19 14:24:38 VERBOSE[4463]: -- Executing
Dial("SIP/192.168.0.6-08137090", "Zap/1/4502") in new stack<br>
Jul 19 14:24:38 NOTICE[4463]: Unable to create channel of type 'Zap'<br>
Jul 19 14:24:38 VERBOSE[4463]: == Everyone is busy/congested at this
time<br>
Jul 19 14:24:38 DEBUG[4463]: Exiting with DIALSTATUS=CHANUNAVAIL.</small></i></small><br>
<br>
zttool say:<br>
<i><small><small>OK Digium Wildcard TE110P T1/E1 Card 0<br>
<br>
Current Alarms: No alarms. <br>
Sync Source: Internally clocked<br>
IRQ Misses: 14<br>
Bipolar Viol: 0<br>
Tx/Rx Levels: 0/ 0 <br>
Total/Conf/Act: 31/ 31/ 0<br>
1111111111222222222333<br>
1234567890123456789012345789012</small></small></i><br>
<br>
I thing that the other end it's ok because I can close the ISDN Link
between the two machines.<br>
<br>
Thanks<br>
Lincoln<br>
<br>
Moises Silva wrote:
<blockquote
cite="midc4d05cbe0607190938v37319d6er60898306b4d76161@mail.gmail.com"
type="cite">Are you sure the other end is configured properly?
<br>
What does "zttool" says?
<br>
Have you turned on all the asterisk debug messages to look further?
<br>
<br>
Regards
<br>
<br>
On 7/19/06, Lincoln Zuljewic Silva <a class="moz-txt-link-rfc2396E" href="mailto:lsilva@corsidian.com"><lsilva@corsidian.com></a> wrote:
<br>
<blockquote type="cite"><br>
Hello all. I have a Digitum TE110P board configured and working (I
think
<br>
that it's working). When I configure in extensions.conf to a extension
route
<br>
to that board I get "Unable to create channel of type 'Zap'" on log.
<br>
<br>
Here are some configuration:
<br>
<br>
lspci -vv
<br>
0000:01:07.0 Network controller: Tiger Jet Network Inc. Tiger3XX
Modem/ISDN
<br>
interface
<br>
Subsystem: Unknown device 795e:0001
<br>
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr-
<br>
Stepping- SERR+ FastB2B-
<br>
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort-
<br>
<TAbort- <MAbort- >SERR- <PERR-
<br>
Latency: 64 (250ns min, 32000ns max)
<br>
Interrupt: pin A routed to IRQ 11
<br>
Region 0: I/O ports at c800 [size=256]
<br>
Region 1: Memory at fc5ff000 (32-bit, non-prefetchable)
[size=4K]
<br>
Capabilities: [40] Power Management version 2
<br>
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
<br>
PME(D0+,D1-,D2+,D3hot+,D3cold-)
<br>
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
<br>
<br>
ztcfg -vv
<br>
Zaptel Configuration
<br>
======================
<br>
<br>
SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
<br>
<br>
Channel map:
<br>
<br>
Channel 01: Individual Clear channel (Default) (Slaves: 01)
<br>
Channel 02: Individual Clear channel (Default) (Slaves: 02)
<br>
Channel 03: Individual Clear channel (Default) (Slaves: 03)
<br>
Channel 04: Individual Clear channel (Default) (Slaves: 04)
<br>
Channel 05: Individual Clear channel (Default) (Slaves: 05)
<br>
Channel 06: Individual Clear channel (Default) (Slaves: 06)
<br>
Channel 07: Individual Clear channel (Default) (Slaves: 07)
<br>
Channel 08: Individual Clear channel (Default) (Slaves: 08)
<br>
Channel 09: Individual Clear channel (Default) (Slaves: 09)
<br>
Channel 10: Individual Clear channel (Default) (Slaves: 10)
<br>
Channel 11: Individual Clear channel (Default) (Slaves: 11)
<br>
Channel 12: Individual Clear channel (Default) (Slaves: 12)
<br>
Channel 13: Individual Clear channel (Default) (Slaves: 13)
<br>
Channel 14: Individual Clear channel (Default) (Slaves: 14)
<br>
Channel 15: Individual Clear channel (Default) (Slaves: 15)
<br>
Channel 16: D-channel (Default) (Slaves: 16)
<br>
Channel 17: Individual Clear channel (Default) (Slaves: 17)
<br>
Channel 18: Individual Clear channel (Default) (Slaves: 18)
<br>
Channel 19: Individual Clear channel (Default) (Slaves: 19)
<br>
Channel 20: Individual Clear channel (Default) (Slaves: 20)
<br>
Channel 21: Individual Clear channel (Default) (Slaves: 21)
<br>
Channel 22: Individual Clear channel (Default) (Slaves: 22)
<br>
Channel 23: Individual Clear channel (Default) (Slaves: 23)
<br>
Channel 24: Individual Clear channel (Default) (Slaves: 24)
<br>
Channel 25: Individual Clear channel (Default) (Slaves: 25)
<br>
Channel 26: Individual Clear channel (Default) (Slaves: 26)
<br>
Channel 27: Individual Clear channel (Default) (Slaves: 27)
<br>
Channel 28: Individual Clear channel (Default) (Slaves: 28)
<br>
Channel 29: Individual Clear channel (Default) (Slaves: 29)
<br>
Channel 30: Individual Clear channel (Default) (Slaves: 30)
<br>
Channel 31: Individual Clear channel (Default) (Slaves: 31)
<br>
<br>
31 channels configured.
<br>
<br>
My zaptel.cfg
<br>
span=1,0,0,cas,hdb3
<br>
loadzone=us
<br>
defaultzone=us
<br>
bchan=1-15,17-31
<br>
dchan=16
<br>
<br>
My zapata.conf
<br>
[channels]
<br>
context=customer
<br>
signalling=pri_cpe
<br>
channel => 1
<br>
<br>
My extensions.conf
<br>
exten => 4502,1,Dial(Zap/1/4502)
<br>
<br>
show channels in Asterisk CLI:
<br>
Channel (Context Extension Pri ) State Appl.
Data
<br>
0 active channel(s)
<br>
<br>
zap show channels in Asterisk CLI:
<br>
Chan Extension Context Language MusicOnHold
<br>
pseudo customer
<br>
1 customer
<br>
<br>
zap show channel 1 in Asterisk CLI:
<br>
hannel: 1>
<br>
File Descriptor: 10
<br>
Span: 1
<br>
Extension:
<br>
Dialing: no
<br>
Context: corsidian
<br>
Caller ID string:
<br>
Destroy: 0
<br>
InAlarm: 0
<br>
Signalling Type: PRI Signalling
<br>
Owner: <None>
<br>
Real: <None>
<br>
Callwait: <None>
<br>
Threeway: <None>
<br>
Confno: -1
<br>
Propagated Conference: -1
<br>
Real in conference: 0
<br>
DSP: no
<br>
Relax DTMF: no
<br>
Dialing/CallwaitCAS: 0/0
<br>
Default law: alaw
<br>
Fax Handled: no
<br>
Pulse phone: no
<br>
Echo Cancellation: 0 taps unless TDM bridged, currently OFF
<br>
PRI Flags:
<br>
PRI Logical Span: Implicit
<br>
Actual Hookstate: Onhook
<br>
<br>
When I dial 4502 in the softphone I get "Unable to create channel of
type
<br>
'Zap'".
<br>
Could anybody give to me a little help ?
<br>
<br>
Thanks a lot !
<br>
Lincoln
<br>
<br>
<br>
_______________________________________________
<br>
--Bandwidth and Colocation provided by Easynews.com --
<br>
<br>
asterisk-users mailing list
<br>
To UNSUBSCRIBE or update options visit:
<br>
<br>
<a class="moz-txt-link-freetext" href="http://lists.digium.com/mailman/listinfo/asterisk-users">http://lists.digium.com/mailman/listinfo/asterisk-users</a>
<br>
<br>
<br>
<br>
</blockquote>
<br>
<br>
</blockquote>
<br>
</body>
</html>