[asterisk-users] PJSIP does not qualify contacts after starting Asterisk

[Annus Fictus]

Hello,

in which moment Asterisk leave to qualify the realtime endpoint? When 
you restart Asterisk?

On my asterisk 13.9.1, qualify on realtime endpoints works correctly. My 
sorcery.conf:

[res_pjsip]
endpoint=realtime,ps_endpoints
endpoint=config,pjsip.conf,criteria=type=endpoint
auth=realtime,ps_auths
auth=config,pjsip.conf,criteria=type=auth
aor=realtime,ps_aors
aor=config,pjsip.conf,criteria=type=aor
domain_alias=realtime,ps_domain_aliases
domain_alias=config,pjsip.conf,criteria=type=domain_alias
contact=realtime,ps_contacts
contact=config,pjsip.conf,criteria=type=contact

[res_pjsip_endpoint_identifier_ip]
identify=realtime,ps_endpoint_id_ips
identify=config,pjsip.conf,criteria=type=identify

Regards


El 13/06/2016 a las 14:16, Francisco Valentin Vinagrero escribió:
>
> Hi,
>
> Yes, we’re implementing the dialplan in realtime too.
>
> Here the contents of sorcery.conf:
>
> [res_pjsip]
>
> endpoint=realtime,ps_endpoints
>
> aor=realtime,ps_aors
>
> contact=realtime,ps_contacts
>
> [res_pjsip_endpoint_identifier_ip]
>
> identify=realtime,ps_endpoint_id_ips
>
> Cheers, Francisco.
>
> *From:*asterisk-users-bounces at lists.digium.com 
> [mailto:asterisk-users-bounces at lists.digium.com] *On Behalf Of *Annus 
> Fictus
> *Sent:* 13 June 2016 14:11
> *To:* Asterisk Users Mailing List - Non-Commercial Discussion 
> <asterisk-users at lists.digium.com>
> *Subject:* Re: [asterisk-users] PJSIP does not qualify contacts after 
> starting Asterisk
>
> Hello Francisco,
>
> you have to use:
>
> extensions => odbc,asterisk
>
> only if you want use dialplan in Realtime
>
> can you share your sorcery.conf file?
>
> Regards
>
> El 13/06/2016 a las 10:21, Francisco Valentin Vinagrero escribió:
>
>     Hi all,
>
>     (sending this again from the correct address)
>
>     I’m running Asterisk 13.8.0 (I need to check if that happens with
>     13.9.1 too when I have the time to build it) with PJSIP realtime
>     config.
>
>     I’ve defined several aors in the table ps_aors, like this (real
>     url replaced by myurl):
>
>     *CLI> pjsip show aor pbx-node-1
>
>           Aor: <Aor..............................................>
>     <MaxContact>
>
>         Contact: <Aor/ContactUri............................>
>     <Hash....> <Status> <RTT(ms)..>
>
>      =========================================================================================
>
>
>           Aor: pbx-node-1 0
>
>         Contact:  pbx-node-1/sip:myurl:5060 771bf6a7d4 Created      
>     0.000
>
>      ParameterName        : ParameterValue
>
>      ===================================================
>
>      authenticate_qualify : false
>
>      contact              : sip:myurl:5060
>
>     default_expiration : 3600
>
>      mailboxes :
>
>      max_contacts : 0
>
>     maximum_expiration   : 7200
>
>      minimum_expiration   : 60
>
>      outbound_proxy       : sip:myurl:5060
>
>      qualify_frequency    : 30
>
>      qualify_timeout      : 3.000000
>
>      remove_existing      : false
>
>      support_path         : false
>
>     So I think that those aors should be qualified automatically when
>     I run Asterisk, but if I do “/pjsip show contacts”/, I get that it
>     was just Created but not qualified:
>
>     *CLI> pjsip show contacts
>
>       Contact: <Aor/ContactUri..............................>
>     <Hash....> <Status> <RTT(ms)..>
>
>     =========================================================================================
>
>       Contact:  pbx-node-1/sip:myurl:5060 771bf6a7d4 Created       0.000
>
>     And not a single OPTIONS message if I take a trace…
>
>     If I want Asterisk to start sending OPTIONS, I need to do pjsip
>     reload and after that, they are qualified and their status changes
>     dynamically:
>
>     *CLI> pjsip show contacts
>
>       Contact: <Aor/ContactUri..............................>
>     <Hash....> <Status> <RTT(ms)..>
>
>     =========================================================================================
>
>       Contact:  pbx-node-1/sip:myurl.ch:5060 771bf6a7d4 Avail        
>     8.833
>
>     The extconfig.conf file looks like this:
>
>     [settings]
>
>     ps_endpoints => odbc,asterisk
>
>     ps_auths => odbc,asterisk
>
>     ps_aors => odbc,asterisk
>
>     ps_domain_aliases => odbc,asterisk
>
>     ps_endpoint_id_ips => odbc,asterisk
>
>     ps_contacts => odbc,asterisk
>
>     extensions => odbc,asterisk
>
>     Any idea why I need to reload PJSIP if I want the aors to be
>     qualified?
>
>     Cheers, Francisco.
>
>
>
>
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20160613/2e164df5/attachment-0001.html>