[asterisk-users] "dahdi show channels" no such command

[Joseph Towery]

Here are the commands

asteriskpbx at pbxmain:/etc/dahdi$ dahdi_cfg -vvv
DAHDI Tools Version - 2.7.0.2

DAHDI Version: 2.7.0.1
Echo Canceller(s): MG2
Configuration
======================


Channel map:

Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 04)
Channel 05: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 05)
Channel 06: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 06)
Channel 07: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 07)
Channel 08: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 08)

8 channels to configure.

Setting echocan for channel 1 to mg2
Setting echocan for channel 2 to mg2
Setting echocan for channel 3 to mg2
Setting echocan for channel 4 to mg2
Setting echocan for channel 5 to mg2
Setting echocan for channel 6 to mg2
Setting echocan for channel 7 to mg2
Setting echocan for channel 8 to mg2
asteriskpbx at pbxmain:/etc/dahdi$



pbxmain*CLI> module show like chan_dahdi.so
Module                         Description                              Use Count
chan_dahdi.so                  DAHDI Telephony Driver w/PRI             0       
1 modules loaded



>________________________________
> From: Eric Wieling <EWieling at nyigc.com>
>To: Joseph Towery <techyjt at bellsouth.net>; Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at lists.digium.com> 
>Sent: Thursday, December 5, 2013 9:09 PM
>Subject: RE: [asterisk-users] "dahdi show channels" no such command
> 
>
>Run "dahdi_cfg -vvv" to verify DAHDI kernel modules are loaded and configured correctly.
>
>Verify chan_dahdi.so is built and located in your Asterisk modules directory, usually /usr/lib/asterisk/modules/  If there is no chan_dahdi.so chances are you built Asterisk before installing DAHDI.  Rerun ./configure or run "make distclean" and then rerun ./configure to rebuild Asterisk.
>
>Use the command "module show like dahdi" in the Asterisk CLI to verify chan_dahdi.so is loaded.  If it isn't loaded then chances are you have a chan_dahdi.conf issue.
>
>
>-----Original Message-----
>From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Joseph Towery
>Sent: Thursday, December 05, 2013 8:41 PM
>To: asterisk-users at lists.digium.com
>Subject: [asterisk-users] "dahdi show channels" no such command
>
>I have followed the instructions in Asterisk The Definitive Guide 4th edition.  Once I load DAHDI I run the dahdi show channels command and get no such command.  I have setup all the conf files.  I compiled DADHI prior to Asterisk.
>
>Any ideas?
>
>
>
>
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20131205/b2e0895b/attachment.html>