[asterisk-users] Fwd: Block Collect Calls on ISDN trunk

[Rafael dos Santos Saraiva]

Richard

I tried to leave these fields empty. It did not work. Not appear IE74 in
the debug.
The possibility exists that the carrier does not be sending?

Att,
Rafael Saraiva




2012/2/17 Richard Mudgett <rmudgett at digium.com>

> I had not noticed that you switched to direct email earlier.
>
> ----- Original Message -----
> > Switchtype: euroisdn
> >
> >
> > This is my chan_dadhi.conf
> >
> > [trunkgroups]
> > trunkgroup=>1,16
> > spanmap=>1,1
>
> The trunkgroups section is only needed if you are using NFAS and
> its presence may cause issues for switches that do not support it.
> NFAS is not supported by euroisdn or qsig.
>
> After looking again at your traces, the STATUS messages are complaining
> about the channel id indicated by Asterisk.  The trunk groups setup
> you have here is causing it.
>
> Just make this an empty section.
>
> >
> >
> > [channels]
> > language=pt_BR
> > hidecallerid=no
> > usecallerid=yes
> > callwaiting=yes
> > callwaitingcallerid=yes
> > threewaycalling=yes
> > transfer=yes
> > canpark=yes
> > cancallforward=yes
> > callreturn=yes
> > echocancel=yes
> > echocancelwhenbridged=no
> > callerid=asreceived
> > switchtype=euroisdn ;qsig
> > signalling=pri_cpe
> > context=PABX
> > facilityenable=yes
> > hidecalleridname=no
> > ;aoc_enable=s,d,e
> > imediate=yes
> > ;busydetect=yes
> > overlapdial=yes
> > inbanddisconnect=yes
> > priindication=inband ;outofband
> > nsf=none
> > ;qsigchannelmapping=logical
> > pridialplan=unknown
> > prilocaldialplan=unknown
> > ;internationalprefix=00
> > ;nationalprefix=55
> > ;localprefix=5551
> > ;privateprefix=55513205
> > ;unknownprefix=
> > service_message_support=yes
> > mohinterpret=default
> > discardremoteholdretrieval=yes
> > group=1
> > channel=>1-15,17-31
> >
> >
> > And system.conf:
> >
> >
> >
> > loadzone=br
> > defaultzone=br
> >
> >
> >
> >
> > #span=1,1,0,cas,hdb3
> > #cas=1-15,17-31:1101
> >
> >
> > span=1,0,0,ccs,hdb3
> > dchan=16
> > bchan=1-15,17-31
> >
> >
> >
> > Att,
> > Rafael Saraiva
> >
> >
> >
> >
> >
> > 2012/2/17 Richard Mudgett < rmudgett at digium.com >
> >
> >
> > > I could not send attachments to the list.
> > > Att,
> > > Rafael Saraiva
> >
> > You could have put the traces inline like you did the console
> > capture.
> > However, the attached files were oddly garbled in that lines were
> > duplicated. It looks like your network switch does not like the
> > PROCEEDING or ALERTING messages.
> >
> > The SETUP message did not have any differences between a normal call
> > and a collect call that I could see. So there does not appear to be a
> > way to tell the calls apart.
> >
> > What is the configured switch type?
> >
> > Richard
> >
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20120223/c53cc723/attachment.htm>