[asterisk-users] Problem installing FXS module in old digium 4 channel tdm card

[C F]

I just installed an FXS module onto a 4 channel tdm thats about 5
years old and it wont work. Running dmesg I can see the following
error:

Zapata Telephony Interface Registered on major 196
Freshmaker version: 71
Freshmaker passed register test
!!!!!!! LOOP_CLOSE_TRES  iREG 1C = 1  should be 1000
!!!!!!! RING_TRIP_TRES  iREG 1D = 8000  should be 3600
!!!!!!! COMMON_MIN_TRES  iREG 1E = 0  should be 1000
!!!!!!! COMMON_MAX_TRES  iREG 1F = 0  should be 200
!!!!!!! PWR_ALARM_Q1Q2  iREG 20 = 1480  should be 7C0
!!!!!!! PWR_ALARM_Q3Q4  iREG 21 = 37C0  should be 2600
!!!!!!! PWR_ALARM_Q5Q6  iREG 22 = 3D70  should be 1B80
!!!!!!! LOOP_CLOSURE_FILTER  iREG 23 = 3970  should be 8000
!!!!!!! RING_TRIP_FILTER  iREG 24 = 78E0  should be 320
!!!!!!! TERM_LP_POLE_Q1Q2  iREG 25 = 8B60  should be 8C
!!!!!!! TERM_LP_POLE_Q3Q4  iREG 26 = 6A40  should be 100
!!!!!!! TERM_LP_POLE_Q5Q6  iREG 27 = 8070  should be 10
!!!!!!! CM_BIAS_RINGING  iREG 28 = FFFF  should be C00
!!!!!!! DCDC_MIN_V  iREG 29 = FFFF  should be C00
!!!!!!! DCDC_XTRA  iREG 2A = FFFF  should be 1000
!!!!!!! LOOP_CLOSE_TRES_LOW  iREG 2B = FFFF  should be 1000
 !!!!! Init Indirect Registers UNSUCCESSFULLY.
Indirect Registers failed verification.
!!!!!!! LOOP_CLOSE_TRES  iREG 1C = 1  should be 1000
!!!!!!! RING_TRIP_TRES  iREG 1D = 8000  should be 3600
!!!!!!! COMMON_MIN_TRES  iREG 1E = 0  should be 1000
!!!!!!! COMMON_MAX_TRES  iREG 1F = 0  should be 200
!!!!!!! PWR_ALARM_Q1Q2  iREG 20 = 1480  should be 7C0
!!!!!!! PWR_ALARM_Q3Q4  iREG 21 = 37C0  should be 2600
!!!!!!! PWR_ALARM_Q5Q6  iREG 22 = 3D70  should be 1B80
!!!!!!! LOOP_CLOSURE_FILTER  iREG 23 = 3970  should be 8000
!!!!!!! RING_TRIP_FILTER  iREG 24 = 78E0  should be 320
!!!!!!! TERM_LP_POLE_Q1Q2  iREG 25 = 8B60  should be 8C
!!!!!!! TERM_LP_POLE_Q3Q4  iREG 26 = 6A40  should be 100
!!!!!!! TERM_LP_POLE_Q5Q6  iREG 27 = 8070  should be 10
!!!!!!! CM_BIAS_RINGING  iREG 28 = FFFF  should be C00
!!!!!!! DCDC_MIN_V  iREG 29 = FFFF  should be C00
!!!!!!! DCDC_XTRA  iREG 2A = FFFF  should be 1000
!!!!!!! LOOP_CLOSE_TRES_LOW  iREG 2B = FFFF  should be 1000
 !!!!! Init Indirect Registers UNSUCCESSFULLY.
Indirect Registers failed verification.
Module 0: FAILED FXS (FCC)
Module 1: Installed -- AUTO FXO (FCC mode)
Module 2: Installed -- AUTO FXO (FCC mode)
Module 3: Installed -- AUTO FXO (FCC mode)
Found a Wildcard TDM: Wildcard TDM400P REV E/F (3 modules)

Does this have to do with the fact that the module is way newer than the card?

TIA
C F