[asterisk-users] B410P and Patton smartnode : any success ?

[Leonardo Pistone]

Hi Oliver,

I haven't tried exactly your setup, but:

1. dss1 patton settings is ok for me for european ISDN.

2. have you installed libpri? what about dahdi show status? and dahdi 
show channels?

Try module reload chan_dahdi.so. It should say
-- Reloading module 'chan_dahdi.so' (DAHDI Telephony Driver w/PRI)
where w/PRI is particularly important. If it doesn't, recompile and 
install libpri, dahdi and asterisk and see if that works.

Ciao

Leo

On 09/05/10 12:14, Olivier wrote:
> Hi,
>
> 1. Has someone met any success at all, connecting a Digium B410P to a
> Patton Smartnode 4638 (with latest 5.3 firmware) ?
>
>
> 2. If positive, then, which signalling was used on both sides ?
>
> My project's goal is use a Patton Smartnode 4638 to act as telco BRI
> lines, from a B410P-enabled asterisk box.
> In my testings, I can see channel is respectively up (with patton web
> server status page) and OK (with dahdi_tool) from both sides but I can't
> dial a single call ("Unable to create DAHDI for unknown reason...") from
> asterisk to patton.
>
> In my setup, my main settings are :
> Smartnode side:     dss1,Net,pp,q931,q921
> B410P side:
> euroisdn,bri_cpe,span=1,1,0,ccs,ami,bchan=1-2,hardhdlc=3
>
> Both devices lights are green but I think this only means layer1 diag is OK.
> Looking at http://en.wikipedia.org/wiki/Digital_Subscriber_System_No._1,
> I would say DSS1 and EuroISDN are the same (but that doesn't mean both
> implementations are compliant to each other).
>
> The mostly troubling thing is :
> CLI> pri show spans
> CLI>
>
> Though with dmesg :
> [ 3923.671739] dahdi: Version: SVN-trunk-r7640M
> [ 3923.683743] wcb4xxp 0000:01:0a.0: probe called for b4xx...
> [ 3923.683743] ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level,
> low) -> IRQ 21
> [ 3923.683743] wcb4xxp 0000:01:0a.0: Identified Wildcard B410P
> (controller rev 1) at 0001dff0, IRQ 21
> [ 3923.683743] wcb4xxp 0000:01:0a.0: VPM 0/1 init: chip ver 33
> [ 3923.692430] wcb4xxp 0000:01:0a.0: VPM 1/1 init: chip ver 33
> [ 3923.704465] wcb4xxp 0000:01:0a.0: Hardware echo cancellation enabled.
> [ 3923.704561] wcb4xxp 0000:01:0a.0: Port 1: TE mode
> [ 3923.708484] wcb4xxp 0000:01:0a.0: Port 2: TE mode
> [ 3923.708484] wcb4xxp 0000:01:0a.0: Port 3: TE mode
> [ 3923.708484] wcb4xxp 0000:01:0a.0: Port 4: TE mode
> [ 3923.708484] wcb4xxp 0000:01:0a.0: Did not do the highestorder stuff
> [ 3923.794449] dahdi_echocan_oslec: Registered echo canceler 'OSLEC'
> [ 3923.795577] dahdi: Registered tone zone 2 (France)
> [ 3923.811320] wcb4xxp 0000:01:0a.0: new card sync source: port 1
>
> /var/log/asterisk/full does show any warning or error related to Dahdi/PRI.
>
> # cat /proc/interrupts
>             CPU0       CPU1
>    0:         84          0   IO-APIC-edge      timer
> ...
>   21:    4030670          0   IO-APIC-fasteoi   b4xxp
>
>
> Regards
>


-- 
Leonardo Pistone
SISPAC

Tel. 0114540111, Fax 0114540160