[asterisk-users] VPMADT032 Failed! Unable to ping the DSP (2)!

[Warren Selby]

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a
week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1
VPMADT032 Module, hooked up to 5 analog lines.  I get the error message
referenced in the subject in my dmesg output everytime I load / reload DAHDI
using the command "system dahdi start/restart".  When I make an outbound
call over these analog lines, I'm told in the CLI " WARNING[22601]:
chan_dahdi.c:2685 dahdi_enable_ec: Unable to enable echo cancellation on
channel 5 (No such device)", and there is noticeable echo on the line,
hearable by the caller inside the office, not by the recipient outside the
office.  When I make an inbound call, I get the same message, with echo
still heard by the person inside the office, and not outside.  I've run
fxotune -i 4 -e 5 also, and still receive the same output.

Below is my chan_dahdi.conf, my system.conf, my dmesg output while loading
dahdi, if you need anything else let me know:

*** chan_dahdi.conf ***
[trunkgroups]

[channels]
usecallerid = yes
hidecallerid = no
threewaycalling = no
echocancel = yes
echocancelwhenbridged = no
rxgain = 0.0
txgain = 0.0

group = 1
echocancel = yes
signalling = fxs_ks
context = incoming
channel = 1-5


*** system.conf ***
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Span 1: WCTDM/0 "Wildcard AEX800 Board 1" (MASTER)
fxsks=1-5

# Global data

loadzone        = us
defaultzone     = us


*** dmesg output ***
dahdi: Telephony Interface Registered on major 196
dahdi: Version: 2.3.0.1
PCI: Enabling device 0000:03:08.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 19 (level, low) -> IRQ 177
wctdm24xxp 0000:03:08.0: Port 1: Installed -- AUTO FXO (FCC mode)
wctdm24xxp 0000:03:08.0: Port 2: Installed -- AUTO FXO (FCC mode)
wctdm24xxp 0000:03:08.0: Port 3: Installed -- AUTO FXO (FCC mode)
wctdm24xxp 0000:03:08.0: Port 4: Installed -- AUTO FXO (FCC mode)
wctdm24xxp 0000:03:08.0: Port 5: Installed -- AUTO FXO (FCC mode)
wctdm24xxp 0000:03:08.0: Port 6: Installed -- AUTO FXO (FCC mode)
wctdm24xxp 0000:03:08.0: Port 7: Installed -- AUTO FXO (FCC mode)
wctdm24xxp 0000:03:08.0: Port 8: Installed -- AUTO FXO (FCC mode)
wctdm24xxp 0000:03:08.0: VPM100: Not Present
wctdm24xxp 0000:03:08.0: Booting VPMADT032
wctdm24xxp 0000:03:08.0: VPMADT032 Failed! Unable to ping the DSP (2)!
wctdm24xxp 0000:03:08.0: Found a Wildcard TDM: Wildcard AEX800 (0 digital
modules, 8 analog modules)
dahdi: Registered tone zone 0 (United States / North America)
wctdm24xxp 0000:03:08.0: -- Setting echo registers:
wctdm24xxp 0000:03:08.0: -- Set echo registers successfully

The last two lines of the dmesg output then repeat over and over again over
time in the dmesg output.

Any help you can offer would be much appreciated!

-- 
Thanks,
--Warren Selby
http://www.selbytech.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100726/99e0ce70/attachment-0001.htm