[asterisk-users] Help: RED alarm on Wildcard TE122 card

[Andreas-Johann Ulvestad]

Hi, I have been trying to get a Wildcard TE122 card running here the
last couple of days.

libpri and zaptel are all installed and configured to E1 specs. The
jumper on the card is on, so configured for E1 (I'm in Norway).

When running zttool, I get 'Alarms: RED' on the single card installed.
Other information in zttool: 
 Current alarms: Red Alarm
 Sync source: Internally clocked
 IRQ Misses: 1
 Bipolar viol: 0
 Tx/Rx levels: 1/0
 Total/conf/act: 31/31/0

There are no IRQ conflicts (cat /proc/interrupt shows only wcte12xp0 on
the relevant IRQ)

The result is the same with or without cable inserted.

The layout is:
 TE122-[3m cable]-[~50m cable]-[NT1 ISDN box from Telenor]

When inserting the cable going into TE122 into an ISDN phone, the phone
works perfectly.

Any suggestions would be greatly appreciated :-)
-------------- next part --------------
# Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) HDB3/CCS/CRC4 RED
span=1,1,1,ccs,hdb3,crc4
# termtype: te
bchan=1-15,17-31
dchan=16

# Global data

loadzone	= no
defaultzone	= no

-------------- next part --------------

Zaptel Version: 1.4.12.1
Echo Canceller: MG2
Configuration
======================

SPAN 1: CCS/HDB3 Build-out: 133-266 feet (DSX-1)

Channel map:

Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: Clear channel (Default) (Slaves: 24)
Channel 25: Clear channel (Default) (Slaves: 25)
Channel 26: Clear channel (Default) (Slaves: 26)
Channel 27: Clear channel (Default) (Slaves: 27)
Channel 28: Clear channel (Default) (Slaves: 28)
Channel 29: Clear channel (Default) (Slaves: 29)
Channel 30: Clear channel (Default) (Slaves: 30)
Channel 31: Clear channel (Default) (Slaves: 31)

31 channels to configure.