[asterisk-users] TE212P octastic initialization failure

[Francois Deppierraz]

Hi,

I'm trying to get a TE212 working on a Dell PowerEdge 1850 running
Debian etch using the latest release of libpri (1.4.0), zaptel (1.4.2.1)
and asterisk (1.4.4). The initilization of the Octasic echo canceller
seems to fail when the wct4xxp module is loaded.

[...]
VPM450: echo cancellation for 64 channels
Failed to open chip, code 00103017!
VPM450: Failed to initialize
[...]

By looking in the zaptel code, this error value (0x00103017) means
cOCT6100_ERR_OPEN_EXTERNAL_MEM_BIST_FAILED.

Is anyone familiar with that problem ?

Thanks for your help.




---
TE212P card: jumpers are set to E1 mode and nothing is connected to that
card at the moment.


# uname -a
Linux ditti-voipa-serv-1 2.6.18-4-amd64 #1 SMP Fri May 4 00:37:33 UTC
2007 x86_64 GNU/Linux
# cat /etc/zaptel.conf
span=1,1,0,ccs,hdb3,crc4
bchan=1-15
dchan=16
bchan=17-31

span=2,1,0,ccs,hdb3,crc4
bchan=32-46
dchan=47
bchan=48-62
# cat /proc/interrupts
           CPU0       CPU1
  0:      42385          0    IO-APIC-edge  timer
  6:          3          0    IO-APIC-edge  floppy
  8:          1          0    IO-APIC-edge  rtc
  9:          0          0   IO-APIC-level  acpi
 14:         64          0    IO-APIC-edge  ide0
169:          0          0   IO-APIC-level  uhci_hcd:usb1
177:          0          0   IO-APIC-level  uhci_hcd:usb2
185:          0          0   IO-APIC-level  uhci_hcd:usb3
193:         19          0   IO-APIC-level  ehci_hcd:usb4
201:       2148          0   IO-APIC-level  ioc0
217:       1153          0   IO-APIC-level  eth1
225:     160247          0   IO-APIC-level  wct2xxp
NMI:         64         42
LOC:      42340      42317
ERR:          0
MIS:          0

# dmesg
[...]
Found TE2XXP at base address fe7ffc00, remapped to ffffc20000004c00
TE2XXP version c01a016a, burst OFF, slip debug: OFF
Octasic optimized!
FALC version: 00000005, Board ID: 00
Reg 0: 0x7daa5400
Reg 1: 0x7daa5000
Reg 2: 0xffffffff
Reg 3: 0x00000000
Reg 4: 0x00000101
Reg 5: 0x00000000
Reg 6: 0xc01a016a
Reg 7: 0x00001300
Reg 8: 0x00000000
Reg 9: 0x00ff0001
Reg 10: 0x0000004a
TE2XXP: Launching card: 0
TE2XXP: Setting up global serial parameters
Found a Wildcard: Wildcard TE210P (3rd Gen)
About to enter spanconfig!
Done with spanconfig!
About to enter spanconfig!
Done with spanconfig!
About to enter startup!
TE2XXP: Span 1 configured for CCS/HDB3/CRC4
wct2xxp: Setting yellow alarm on span 1
timing source auto card 0!
VPM400: Not Present
VPM450: echo cancellation for 64 channels
Failed to open chip, code 00103017!
VPM450: Failed to initialize
Completed startup!
About to enter startup!
TE2XXP: Span 2 configured for CCS/HDB3/CRC4
wct2xxp: Setting yellow alarm on span 2
timing source auto card 0!
SPAN 2: Primary Sync Source
VPM400: Not Present
Failed to get chip capacity, code 0010305e!
Unsupported channel capacity found on VPM module (0).
Completed startup!
[...]
# ztcfg -v

Zaptel Version: 1.4.2.1
Echo Canceller: MG2
Configuration
======================

SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 2: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

62 channels configured.

#