[asterisk-users] [Fwd: PRI Problems]
Rob Schall
rschall at callone.net
Thu Jan 4 10:23:18 MST 2007
I completely missed the 47-47. That wasn't very smart.
With that T1, we don't have the full thing. We are sharing it with
someone else, and 4 of the channels are used elsewhere. It was setup
with em wink, so there isn't a d channel. I'm guessing I should have set
both to 44 and it probably would have worked.
Do you think that could have caused my SPAN 1 error?
Thanks,
Rob
David Gomillion wrote:
> Tell us about channels 45-47...
>
> We have 45-47 defined in zapata.conf, but not in zaptel.conf. Probably
> not the problem, but it might cause some confusion...
>
> Also, look at your timing sources. They don't look quite right to me.
> Spans 1 and 2 are both marked as primary timing sources.
>
> Hope that helps,
> David
>
>
> On 1/4/07, *Rob Schall* <rschall at callone.net
> <mailto:rschall at callone.net>> wrote:
>
> <Correction in my zapata.conf file I used>
>
> Hey Everyone,
>
> So this is a problem I've been having for sometime now. I sent a few
> messages to the list with no luck.
>
> The problem is that when people dial into the Asterisk system
> using DID
> numbers, it works the first time or 2, then I get busy signals.
> A friend recommended I clear out the zapata and zaptel, start
> over, and
> recreate my wanpipe stuff. He thought the problem was with the spans
> themselves.
>
> However, when I use the following information, and restart
> wanrouter, I
> get an error.
>
> Zapata.conf
>
> [channels]
>
> language=en
> context=internal
> switchtype=national
> pridialplan=unknown
> signalling=pri_cpe
> faxdetect=incoming
> usecallerid=yes
> echocancel=yes
> echocancelwhenbridged=yes
> group=0
> channel => 1-23
>
> group=1
> signalling=em_w
> channel => 25-47
>
>
> Zaptel.conf
>
> span=1,1,0,esf,b8zs
> span=2,1,0,esf,b8zs
> bchan=1-23
> dchan=24
> e&m=25-44
>
>
>
> -------------ERROR----------------
> Channel map:
>
> Channel 01: Clear channel (Default) (Slaves: 01)
> Channel 02: Clear channel (Default) (Slaves: 02)
> Channel 03: Clear channel (Default) (Slaves: 03)
> Channel 04: Clear channel (Default) (Slaves: 04)
> Channel 05: Clear channel (Default) (Slaves: 05)
> Channel 06: Clear channel (Default) (Slaves: 06)
> Channel 07: Clear channel (Default) (Slaves: 07)
> Channel 08: Clear channel (Default) (Slaves: 08)
> Channel 09: Clear channel (Default) (Slaves: 09)
> Channel 10: Clear channel (Default) (Slaves: 10)
> Channel 11: Clear channel (Default) (Slaves: 11)
> Channel 12: Clear channel (Default) (Slaves: 12)
> Channel 13: Clear channel (Default) (Slaves: 13)
> Channel 14: Clear channel (Default) (Slaves: 14)
> Channel 15: Clear channel (Default) (Slaves: 15)
> Channel 16: Clear channel (Default) (Slaves: 16)
> Channel 17: Clear channel (Default) (Slaves: 17)
> Channel 18: Clear channel (Default) (Slaves: 18)
> Channel 19: Clear channel (Default) (Slaves: 19)
> Channel 20: Clear channel (Default) (Slaves: 20)
> Channel 21: Clear channel (Default) (Slaves: 21)
> Channel 22: Clear channel (Default) (Slaves: 22)
> Channel 23: Clear channel (Default) (Slaves: 23)
> Channel 24: D-channel (Default) (Slaves: 24)
> Channel 25: E & M (Default) (Slaves: 25)
> Channel 26: E & M (Default) (Slaves: 26)
> Channel 27: E & M (Default) (Slaves: 27)
> Channel 28: E & M (Default) (Slaves: 28)
> Channel 29: E & M (Default) (Slaves: 29)
> Channel 30: E & M (Default) (Slaves: 30)
> Channel 31: E & M (Default) (Slaves: 31)
> Channel 32: E & M (Default) (Slaves: 32)
> Channel 33: E & M (Default) (Slaves: 33)
> Channel 34: E & M (Default) (Slaves: 34)
> Channel 35: E & M (Default) (Slaves: 35)
> Channel 36: E & M (Default) (Slaves: 36)
> Channel 37: E & M (Default) (Slaves: 37)
> Channel 38: E & M (Default) (Slaves: 38)
> Channel 39: E & M (Default) (Slaves: 39)
> Channel 40: E & M (Default) (Slaves: 40)
> Channel 41: E & M (Default) (Slaves: 41)
> Channel 42: E & M (Default) (Slaves: 42)
> Channel 43: E & M (Default) (Slaves: 43)
> Channel 44: E & M (Default) (Slaves: 44)
>
> 44 channels configured.
>
> ZT_SPANCONFIG failed on span 1: Invalid argument (22)
>
>
>
>
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com
> <http://Easynews.com> --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
> <http://lists.digium.com/mailman/listinfo/asterisk-users>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
More information about the asterisk-users
mailing list