[asterisk-users] TE110P and TDM400P

[Marco Mouta]

try this, pls give some feedback
###
/etc/zaptel.conf
span=1,1,0,ccs,hdb3,crc4

fxsks=1-4

bchan=5-19,21-35
dchan=20

loadzone = us
defaultzone=us
###


On 11/22/06, Lincoln Zuljewic Silva <lsilva at corsidian.com> wrote:
>
>  This is the scenarios:
>
> 1 -
> ###
> /etc/zaptel.conf
> span=1,1,0,ccs,hdb3,crc4
> bchan=5-19,21-35
> dchan=20
> fxsks=1-4
> loadzone = us
> defaultzone=us
> ###
> modprobe wcte11xp
> ZT_CHANCONFIG failed on channel 32: No such device or address (6)
> FATAL: Error running install command for wcte11xp
>
> 2 -
>  ###
> /etc/zaptel.conf
> span=1,1,0,ccs,hdb3,crc4
> bchan=5-19,21-35
> dchan=20
> fxsks=1-4
> loadzone = us
> defaultzone=us
> ###
> modprobe wctdm
> ZT_CHANCONFIG failed on channel 5: No such device or address (6)
> FATAL: Error running install command for wctdm
>
> 3 -
>  ###
> /etc/zaptel.conf
> span=1,1,0,ccs,hdb3,crc4
> bchan=1-15,17-31
> dchan=16
> fxsks=32-35
> loadzone = us
> defaultzone=us
> ###
> modprobe wcte11xp....ok
> modprobe wctdm....ok
> modprobe wcfxo....ok
> modprobe wct4xxp....ok
> modprobe zaptel....ok
> ###
> /etc/asterisk/zapata.conf
> [channels]
> context=corsidian
> overlapdial=yes
> immediate=no
> callprogress=yes
> busydetect=no
> switchtype=euroisdn
> signalling=pri_net
> channel => 1-15,17-31
> group=2
> group=1
> callgroup=1
> pickupgroup=1
> signalling=fxs_ks
> channel => 32-35
> ###
>
> tail -f /var/log/asterisk/messages
> Nov 22 15:11:43 ERROR[5524] chan_zap.c: Channel 16 is reserved for
> D-channel.
> Nov 22 15:11:43 ERROR[5524] chan_zap.c: Unable to register channel '1-15'
> Nov 22 15:11:43 WARNING[5524] loader.c: chan_zap.so: load_module failed,
> returning -1
> Nov 22 15:11:43 WARNING[5524] loader.c: Loading module chan_zap.so failed!
>
>
>  ----- Original Message -----
> *From:* Henk Dick <henk at osocoms.com>
> *To:* 'Lincoln Zuljewic Silva' <lsilva at corsidian.com> ; 'Asterisk Users
> Mailing List - Non-Commercial Discussion'<asterisk-users at lists.digium.com>
> *Sent:* Wednesday, November 22, 2006 4:08 PM
> *Subject:* RE: [asterisk-users] TE110P and TDM400P
>
>  I think that you are loading the drivers in the wrong order.  You can
> change the order of loading are first define the E1 followed by the TDM400
>
>
>
> Hope this helps,
>
>
>
> Henk
>
>
>  ------------------------------
>
> *From:* asterisk-users-bounces at lists.digium.com [mailto:
> asterisk-users-bounces at lists.digium.com] *On Behalf Of *Lincoln Zuljewic
> Silva
> *Sent:* woensdag 22 november 2006 20:51
> *To:* asterisk-users at lists.digium.com
> *Subject:* [asterisk-users] TE110P and TDM400P
>
>
>
> Hello all. I have here a TE110P (configured as E1) and a TDM400P (with
> four X100P - FXS). Both boards are recognized by the operating system as
> showed above:
>
>
>
> 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
> Modem/ISDN interface
>         Subsystem: Unknown device b1d9:0003
>         Flags: bus master, medium devsel, latency 64, IRQ 169
>         I/O ports at e800 [size=256]
>         Memory at febff000 (32-bit, non-prefetchable) [size=4K]
>         Capabilities: [40] Power Management version 2
>
>
>
> 0000:08:01.0 Network controller: Tiger Jet Network Inc. Tiger3XX
> Modem/ISDN interface
>         Subsystem: Unknown device 79fe:0001
>         Flags: bus master, medium devsel, latency 64, IRQ 193
>         I/O ports at e400 [size=256]
>         Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
>         Capabilities: [40] Power Management version 2
>
>
>
> The problem is that I cant make the both cards to work together in the
> same server. Here is my /etc/zaptel.conf:
>
>
>
> ###
> fxsks=1-4
> loadzone = us
> defaultzone=us
>
>
>
> span=1,1,0,ccs,hdb3,crc4
> bchan=5-19,21-35
> dchan=20
> ###
>
>
>
> When I load the wctdm module, I get this error: ZT_CHANCONFIG failed on
> channel 5: No such device or address (6). Its sounds like the FXS module its
> tring to configure the channels 5 to 35 (E1 - ISDN Channels - TE110P card).
>
>
>
> Anybody already saw this ? Its possible to use this two cards in the same
> computer ? There is any separator that I can use in zaptel.conf to make
> the load of the modules dont mistakes itself ?
>
>
>
> Here is my versions:
> Debian kernel - 2.6.8
> asterisk-1.2.12.1
> libpri-1.2.4
> zaptel-1.2.11
>
>
>
>
>
> Thanks
>
> Lincoln
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>


-- 
Best regards,

Marco Mouta
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061123/e758e55c/attachment-0001.htm