[Asterisk-Users] Re: Configuring a TDM400P with one FXS port
mohamed kerbachi
kerbachi_m at yahoo.fr
Sun May 21 23:38:25 MST 2006
Hi,
Strange, i get the correct output from the ddmesg:
...
...
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1: Installed -- AUTO FXS/DPO
Module 2: Installed -- AUTO FXS/DPO
Module 3: Installed -- AUTO FXO (FCC mode)
...
...
..
As you see i have TDM400P with 3xFXS + 1xFXO
Try to issue:
modprobe zaptel;modprobe wctdm
And give me the output of the command :"lspci"
--- "M.Hockings" <veeshooter at hockings.net> a écrit :
> mohamed kerbachi wrote:
> > Hi,
> > I have a TDM400P and it works,
> > Send us the output of your "dmesg" command.
> >
> > Regards.
> > --- "M.Hockings" <veeshooter at hockings.net> a écrit
> :
> >
> >> In my attempt to setup a single FXS line I have
> been
> >> following the
> >> instructions for "Telephony Card Drivers" on the
> >> asteriskdocs.org site.
> >> I have managed to checkout, make and install the
> >> zaptel code and can
> >> load the zaptel module but when I attempt to load
> >> the wcfxs module it
> >> tells me:
> >>
> >> ZT_CHANCONFIG failed on channel 1: No such
> device
> >> or address (6)
> >> FATAL: Error running install command for wctdm
> >>
> >> On the card the single FXS module is in the
> position
> >> at the back of the
> >> TDM400P (i.e., closest to the connectors)
> >>
> >> In the /etc/zaptel.conf file I have put the
> >> following at the bottom of
> >> the file:
> >>
> >> fxoks=1
> >> loadzone=us
> >> defaultzone=us
> >>
> >> I have also tried fxoks=4 with the same results
> >> other than that the
> >> channel number changes in the message.
> >>
> >> Any idea what I am configuring incorrectly ?
> >>
> >> Mike
>
> Hi Mohamed, if you can help guide me in the right
> direction I would be
> most appreciative.
>
> The output of dmesg is below.
>
> In the machine is a TDM400P with one FXS, a X101P
> FXO, an ethernet card
> and an old ISA modem.
>
> Mike
>
>
> Linux version 2.6.9-34.EL (buildcentos at build-i386)
> (gcc version 3.4.5
> 20051201 (Red Hat 3.4.5-2)) #1 Wed Mar 8 00:07:35
> CST 2006
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00
> (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000
> (reserved)
> BIOS-e820: 00000000000f0000 - 0000000000100000
> (reserved)
> BIOS-e820: 0000000000100000 - 0000000017ffa000
> (usable)
> BIOS-e820: 0000000017ffa000 - 0000000017ffe000
> (ACPI data)
> BIOS-e820: 0000000017ffe000 - 0000000018000000
> (ACPI NVS)
> 0MB HIGHMEM available.
> 383MB LOWMEM available.
> Using x86 segment limits to approximate NX
> protection
> zapping low mappings.
> On node 0 totalpages: 98298
> DMA zone: 4096 pages, LIFO batch:1
> Normal zone: 94202 pages, LIFO batch:16
> HighMem zone: 0 pages, LIFO batch:1
> DMI 2.0 present.
> ACPI: RSDP (v000 IBM
> ) @ 0x000fe030
> ACPI: RSDT (v001 IBM V66XA 0x00000001 Acer
> 0x00000000) @ 0x17ffa000
> ACPI: FADT (v001 IBM V66XA 0x00000001 Acer
> 0x00000000) @ 0x17ffa028
> ACPI: DSDT (v001 IBM V66XA 0x00001000 MSFT
> 0x0100000a) @ 0x00000000
> ACPI: BIOS age (1998) fails cutoff (2001),
> acpi=force is required to
> enable ACPI
> ACPI: Disabling ACPI support
> Built 1 zonelists
> Kernel command line: ro
> root=/dev/VolGroup00/LogVol00 quiet
> Initializing CPU#0
> CPU 0 irqstacks, hard=c03e7000 soft=c03e6000
> PID hash table entries: 2048 (order: 11, 32768
> bytes)
> Detected 400.948 MHz processor.
> Using tsc for high-res timesource
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 65536 (order: 6,
> 262144 bytes)
> Inode-cache hash table entries: 32768 (order: 5,
> 131072 bytes)
> Memory: 384696k/393192k available (2117k kernel
> code, 7884k reserved,
> 669k data, 144k init, 0k highmem)
> Calibrating delay using timer specific routine..
> 803.04 BogoMIPS
> (lpj=401522)
> Security Scaffold v1.0.0 initialized
> SELinux: Initializing.
> SELinux: Starting in permissive mode
> There is already a security framework initialized,
> register_security failed.
> selinux_register_security: Registering secondary
> module capability
> Capability LSM initialized as secondary
> Mount-cache hash table entries: 512 (order: 0, 4096
> bytes)
> CPU: After generic identify, caps: 0183f9ff 00000000
> 00000000 00000000
> CPU: After vendor identify, caps: 0183f9ff 00000000
> 00000000 00000000
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 512K
> CPU: After all inits, caps: 0183f1ff 00000000
> 00000000 00000040
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: Intel Pentium II (Deschutes) stepping 02
> Enabling fast FPU save and restore... done.
> Checking 'hlt' instruction... OK.
> checking if image is initramfs... it is
> Freeing initrd memory: 983k freed
> NET: Registered protocol family 16
> PCI: PCI BIOS revision 2.10 entry at 0xf0200, last
> bus=1
> PCI: Using configuration type 1
> mtrr: v2.0 (20020519)
> ACPI: Subsystem revision 20040816
> ACPI: Interpreter disabled.
> Linux Plug and Play Support v0.97 (c) Adam Belay
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Probing PCI hardware
> PCI: Probing PCI hardware (bus 00)
> PCI: Using IRQ router PIIX/ICH [8086/7110] at
> 0000:00:07.0
> IBM machine detected. Enabling interrupts during APM
> calls.
> apm: BIOS version 1.2 Flags 0x03 (Driver version
> 1.16ac)
> audit: initializing netlink socket (disabled)
> audit(1148245664.147:1): initialized
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096
> bytes)
> SELinux: Registering netfilter hooks
> Initializing Cryptographic API
> ksign: Installing public key data
> Loading keyring
> - Added public key B4802E7A21D4FA03
> - User ID: CentOS (Kernel Module GPG key)
> Limiting direct PCI/PCI transfers.
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> Real Time Clock Driver v1.12
> Linux agpgart interface v0.100 (c) Dave Jones
> agpgart: Detected an Intel 440BX Chipset.
> agpgart: Maximum main memory to use for agp memory:
> 321M
> agpgart: AGP aperture is 64M @ 0xe0000000
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports,
> IRQ sharing enabled
> ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 16384K
> size 1024 blocksize
> divert: not allocating divert_blk for non-ethernet
> device lo
> Uniform Multi-Platform E-IDE driver Revision:
> 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes;
> override with idebus=xx
> PIIX4: IDE controller at PCI slot 0000:00:07.1
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0x9030-0x9037, BIOS settings:
> hda:pio, hdb:DMA
> ide1: BM-DMA at 0x9038-0x903f, BIOS settings:
> hdc:pio, hdd:DMA
>
=== message truncated ===
___________________________________________________________________________
Faites de Yahoo! votre page d'accueil sur le web pour retrouver directement vos services préférés : vérifiez vos nouveaux mails, lancez vos recherches et suivez l'actualité en temps réel.
Rendez-vous sur http://fr.yahoo.com/set
More information about the asterisk-users
mailing list