[Asterisk-Users] ISDN, TE205P, I'm goind crazy :>

[azyuky]

I know and it's crazy isn't it because this is what i have in my zaptel.conf

bchan=1-15
bchan=17-31
dchan=16
span=1,1,0,ccs,hdb3,crc4
loadzone=sg
defaultzone=sg

The configuration is set to conform to my ISDN30 E1 specifications. And the jumper
on the digium card is closed to enable E1 mode. What have I done wrong here guys.. I
can't get it.. 

--- "Eric \"ManxPower\" Wieling" <eric at fnords.org> wrote:

> ESF/B8ZS is a T-1 config.
> 
> azyuky wrote:
> > Hi Josue and list,
> > 
> > This is part of my dmesg log. Also one other thing, I don't know why the red
> light
> > on span/port 1 of my card keep flashing.. is it normal that way? Or it's
> supposed to
> > mean something? Obviously I have no experience with ISDN before so this is my
> very
> > first try. 
> > 
> > Found TE2XXP at base address e7001000, remapped to e001a000
> > TE2XXP version c01a0164, burst OFF, slip debug: OFF
> > FALC version: 00000005, Board ID: 00
> > Reg 0: 0x1e6ab400
> > Reg 1: 0x1e6ab000
> > Reg 2: 0xffffffff
> > Reg 3: 0x00000000
> > Reg 4: 0x00000000
> > Reg 5: 0x00000000
> > Reg 6: 0xc01a0164
> > Reg 7: 0x00001000
> > Reg 8: 0x00000000
> > Reg 9: 0x00ff0000
> > Reg 10: 0x00000000
> > TE2XXP: Launching card: 0
> > TE2XXP: Setting up global serial parameters
> > Found a Wildcard: Wildcard TE205P 
> > About to enter spanconfig!
> > Done with spanconfig!
> > Registered tone zone 
> > About to enter startup!
> > TE2XXP: Span 1 configured for ESF/B8ZS
> > wct2xxp: Setting yellow alarm on span 1
> > 2G: Got interrupt, status = 0000000d, GIS = 0081
> > SPAN 1: Primary Sync Source
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > VPM: Not Present
> > Completed startup!
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > 2G: Got interrupt, status = 0000000a, GIS = 0080
> > About to enter spanconfig!
> > About to enter startup!
> > TE2XXP: Span 1 configured for ESF/B8ZS
> > SPAN 1: Primary Sync Source
> > Completed startup!
> > Registered tone zone 
> > About to enter spanconfig!
> > About to enter startup!
> > TE2XXP: Span 1 configured for ESF/B8ZS
> > SPAN 1: Primary Sync Source
> > Completed startup!
> > Registered tone zone 
> > About to enter spanconfig!
> > About to enter startup!
> > TE2XXP: Span 1 configured for ESF/B8ZS
> > SPAN 1: Primary Sync Source
> > Completed startup!
> > Registered tone zone 
> > 
> > 
> > --- Josué Conti <josueconti at gmail.com> wrote:
> > 
> >> Hi, test with dmesg and past in list the log´s
> >>
> >> Regards
> >>
> >> Josué
> >>
> >> 2006/5/10, azyuky <azyuky at yahoo.com>:
> >>> Hi guys,
> >>>
> >>> Currently I just purchased the TE205P for the installation of my ISDN30
> >>> setup. I
> >>> compiled, setup the card correctly I think. When I do the ztcfg -vvv it
> >>> shows all 31
> >>> channels clear, with 30 bchannels using for voice ranging from 1-15,
> >>> 17-31, and 16
> >>> is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24
> >>> channels
> >>> configured, and then, when I do a cat /proc/zaptel/2 I see the rest 7
> >>> channels. I
> >>> setup the jumper correctly all closed to use the card in E1 mode.. I'm not
> >>> sure what
> >>> I did wrong here but the card should just display all 31 channels on span
> >>> 1
> >>> (/proc/zaptel/1) instead of spreading it accross to the second span?
> >>>
> >>> Help is appreciated. Thank you.
> 
> -- 
> Now accepting new clients in Birmingham, Atlanta, Huntsville, 
> Chattanooga, and Montgomery.
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
> 


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com