[Asterisk-Users] welltech Wellgate 3804 in SIP mode

[Erick Perez]

one-stage calling function?



On 3/30/06, kevin ling <kevin.ling at amphenol.com.tw> wrote:
>
> Yes,
>
> Same configuration as Martin.
> 1.for incoming call just set the 3804 "hotline" to one sip extension number.
> 2.for outgoing call, you just using regular dail command to pass the phone
> number to 3804  (3804 is a 4FXO port device, the call from ip side always
> pass to FXO Port). You can telnet to the 3804 and enable the one-stage
> calling function.
>
> Regards,
> Kevin
>
>  ________________________________
>  From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf
> Of Martin Joseph
> Sent: Sunday, March 26, 2006 12:13 PM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: Re: [Asterisk-Users] welltech Wellgate 3804 in SIP mode
>
>
>
> On Mar 25, 2006, at 6:26 PM, Erick Perez wrote:
>
>
> Martin,  i guess im in dumb mode today because i don't get what you say, may
> also be because this will be my first welltech to configure.
> what im trying to do is:
> Sorry, I don't know if the 3804 actually uses a similar config setup to my
> 3701a, so it might not be you at all.
>
>
> remote_voip_gateway-------->asterisk----------->fox/fxs/and_international_voip_providers
> call will always go -----> this way, no incoming calls from the right of the
> diagram side to asterisk.
>
> Ok, then if it is similar to mine, all you need to do is set the SIP
> configuration screen for the wellgate. Look under "SIP Config" and "security
> config". Then to dial, you just use (repeated from below):
>
> For outbound ones, I think I just have a regular old
> Dial(SIP/${EXTEN}@2003} in my dialplan where 2003 is the FXO port.
>
> Good Luck,
> Marty
>
> PS I had to reflash my device with the SIP formware, as it arrived with H323
> firmware.
>
>
>
>
>
>
> On 3/23/06, Martin Joseph < ast at stillnewt.org> wrote:
>
> On Mar 22, 2006, at 10:24 PM, Erick Perez wrote:
>
> > Hi, does anybody have a working config or tips to connect the welltech
> > wellgate 3804 (4fxo) unit to asterisk via SIP ?
> > I think I register it via SIP with my * box, but when sending calls
> > from * to the wellgate the unit does not pass the call to any of the
> > fxo ports.
> >
>
> I am using the 3701a, which is a 1 FXO 1 FXS deal.
>
> The trick for me was the "routing table"  or something like that from
> the Web based configuration screen.  There I changed the default for
> the FXO to point to IP, and the IP to default to the FXO.
>
> Then I also have the "line configuration" set so the extension I want
> to ring ie 2020 is the "hotline" for the FXO.
>
> For outbound ones, I think I just have a regular old
> Dial(SIP/${EXTEN}@2003} in my dialplan where 2003 is the FXO port.
>
> HTH?
> Marty
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>
> --
>
> -------------------------------------------
> Erick Perez
> Linux User 376588
> http://counter.li.org/  (Get counted!!!)
> Panama, Republic of Panama
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>


--

-------------------------------------------
Erick Perez
Linux User 376588
http://counter.li.org/  (Get counted!!!)
Panama, Republic of Panama