[Asterisk-Users] module load order for Junghanns qozap and TDM card

[Chris Earle (CBL)]

Maybe this will shed some light about what I'm trying to do:

This is some output from dmesg after this load order:

modprobe zaptel
insmod wcfxs
insmod qozap
----
Zapata Telephony Interface Registered on major 196
Freshmaker version: 73
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1: Installed -- AUTO FXS/DPO
Module 2: Installed -- AUTO FXS/DPO
Module 3: Installed -- AUTO FXS/DPO
Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules)
PCI: Enabling device 02:01.0 (0000 -> 0003)
qozap: Junghanns.NET quadBRI card configured at mem 0xf889b000 IRQ 17 HZ 100
CardID 0
qozap: S/T ports: 4 [ TE TE TE TE ]
qozap: 1 multiBRI card(s) in this box, 4 BRI ports total.


Zaptel Configuration
======================

SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1)
SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1)
SPAN 3: CCS/ AMI Build-out: 399-533 feet (DSX-1)
SPAN 4: CCS/ AMI Build-out: 399-533 feet (DSX-1)

Channel map:

Channel 01: Individual Clear channel (Default) (Slaves: 01)
Channel 02: Individual Clear channel (Default) (Slaves: 02)
Channel 03: D-channel (Default) (Slaves: 03)
Channel 04: Individual Clear channel (Default) (Slaves: 04)
Channel 05: Individual Clear channel (Default) (Slaves: 05)
Channel 06: D-channel (Default) (Slaves: 06)
Channel 07: Individual Clear channel (Default) (Slaves: 07)
Channel 08: Individual Clear channel (Default) (Slaves: 08)
Channel 09: D-channel (Default) (Slaves: 09)
Channel 10: Individual Clear channel (Default) (Slaves: 10)
Channel 11: Individual Clear channel (Default) (Slaves: 11)
Channel 12: D-channel (Default) (Slaves: 12)
Channel 13: FXO Kewlstart (Default) (Slaves: 13)
Channel 14: FXO Kewlstart (Default) (Slaves: 14)
Channel 15: FXO Kewlstart (Default) (Slaves: 15)
Channel 16: FXO Kewlstart (Default) (Slaves: 16)

16 channels configured.

ZT_SPANCONFIG failed on span 1: Invalid argument (22)




any thoughts?




Chris




----- Original Message ----- 
From: "Chris Earle (CBL)" <cearle at cbltech.ca>
To: "'Asterisk Users Mailing List - Non-Commercial Discussion'"
<asterisk-users at lists.digium.com>
Sent: Thursday, March 16, 2006 10:09 AM
Subject: [Asterisk-Users] module load order for Junghanns qozap and TDM card


> Hi all,
>
> I'm trying to get a junghanns QuadBRI to coexist in the same machine as a
> Digium TDM400P card  (so I can run the ISDN lines in and bridge with
analog
> phones plugged into the TDM).
>
> I'm having a problem loading the modules.  If I follow the BRIstuff
> (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod
> qozap.o
> I'm on Debian 2.4.31.
> That works.
> But then I still need the Digium module. (modprobe wctdm)
> I've tried a few different orders.  Sometimes I can get the digium to
load,
> and the qozap.
> but then I get an error on the ztcfg about Span  invalid argument (could
be
> my zaptel.conf I realize...)
>
> *If* I try loading the wctdm after the zaptel and qozap, the server
freezes!
> Some loop about qozap - dropped audio card....
>
> I don't know if the quadBRI and the TDM are conflicting/sharing the zaptel
> module, or if I need to modprobe zaptel before each of them? and in what
> order?
>
> Any suggestions appreciated... I haven't even got to figuring out what I
can
> do with chan_capi, just want to get the BRI card on and stuff.
>
> Thanks for any ideas!
>
>
> --
> Chris Earle
>
>
> -- 
> This message has been scanned for viruses and dangerous content by
> MailScanner, and is believed to be clean.
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users


-- 
This message has been scanned for viruses and dangerous content by
MailScanner, and is believed to be clean.