[Asterisk-Users] echo problem + choppy sound
Mojo with Horan & Company, LLC
mojo at horanappraisals.com
Wed Mar 15 17:34:22 MST 2006
Have you tried with apic turned off? And, on another note, our system
had bad sound (you might describe it as choppy) with acpi enabled.
Do you have access to a milliwatt test line?
Moj
sdgesa gaeharth wrote:
> thanks for the info.
>
> it is not sharing an irq:
>
> 0: 59840409 59803082 IO-APIC-edge timer
> 8: 1 0 IO-APIC-edge rtc
> 9: 0 0 IO-APIC-level acpi
> 11: 0 0 IO-APIC-level ohci_hcd:usb1
> 14: 2141851 2143209 IO-APIC-edge ide0
> 177: 111558 111273 IO-APIC-level aic7xxx
> 185: 15 0 IO-APIC-level aic7xxx
> 193: 736328 748953 IO-APIC-level eth0
> 201: 239290099 239259220 IO-APIC-level wctdm
> NMI: 0 0
> LOC: 119645889 119645888
> ERR: 0
> MIS: 0
>
>
> I checked the switch. The net connection is running at full duplex:
>
> FastEthernet0/15 is up, line protocol is up (connected)
> Hardware is Fast Ethernet, address is 0013.80b7.e24f (bia 0013.80b7.e24f)
> MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulatio n ARPA, loopback not set
> Keepalive set (10 sec)
> Full-duplex, 100Mb/s, media type is 100BaseTX
> input flow-control is unsupported output flow-control is unsupported
> ARP type: ARPA, ARP Timeout 04:00:00
> Last input never, output 00:00:03, output hang never
> Last clearing of "show interface" counters never
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
> Queueing strategy: fifo
> Output queue: 0/40 (size/max)
> 5 minute input rate 31000 bits/sec, 15 packets/sec
> 5 minute output rate 32000 bits/sec, 15 packets/sec
> 679924 packets input, 225898296 bytes, 0 no buffer
> Received 3803 broadcasts (0 multicast)
> 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
> 0 watchdog, 5 multicast, 0 pause input
> 0 input packets with dribble condition detected
> 689110 packets output, 145860377 bytes, 0 underruns
> 0 output errors, 0 collisions, 2 interface resets
> 0 babbles, 0 late collision, 0 deferred
> 0 lost carrier, 0 no carrier, 0 PAUSE output
> 0 output buffer failures, 0 output buffers swapped out
>
> */Rich Adamson <radamson at routers.com>/* wrote:
>
> Based only on what I see below (from previous posts), it sounds like
> you
> have two separate issues going on: 1) echo, and, 2) choppy sound. Those
> should be analyzed as two problems (not one).
>
> You will find plenty of posts in the archives relative to both. In
> general terms, the choppy audio m ost often is caused by shared IRQ's
> when using a x100p or TDM400 card, and sometimes from a misconfigured
> ethernet nic on the asterisk machine. For the nic card, ensure you are
> running full duplex on the nic "and" whatever the nic is plugged in to.
> Both need to be the same (half duplex will work in a low usage
> environment, but full duplex is preferred.)
>
> For the IRQ issue (and we are all assuming you are using a TDM04b card
> since you really didn't say), do a 'cat /proc/interrupts' and make sure
> your TDM card is on its own IRQ. If it is shared with other devices, it
> is likely the cause for choppy audio. You'll see the TDM driver
> wctdm on
> that list. If it is shared, then move the TDM card from one pci slot to
> another to get it on its own IRQ.
>
> The echo problem is going to be almost aways related to "too high" of
> gains in zapata.conf. Your rxgain=10 and txgain=10 are way too high as
> others have already noted. Try reducing those to 0 and restart asterisk.
> Then increase the values (if needed) by increments of 2 until you
> find a
> balance between low volume and echo. I'd suggest doing that "after"
> resolving the IRQ/choppy audio issues.
>
>
> > I have done this but I still get choppy sound and echo on some calls
> >
> > thanks
> >
> > */Giovanni Miano /* wrote:
> >
> > Of course,
> > Echo is 2 types: electric and ambiental.
> >
> > If u gain rx o tx more than you need, its return in recive and
> gen echo
> >
> > Try to decrase value, try to set 0 or .. in samecase -1 -2...
> >
> > 2006/3/13, sdgesa gaeharth
> > >:
> >
> > Can you explain why?
> >
> >
> > */Giovanni Miano
> > >/* wrote:
> >
> &g t; rxgain=10.0
> > txgain=10.0
> >
> > ????
> >
> > Maybe this is a problem
> >
> >
> > 2006/3/13, sdgesa gaeharth < pollux1234567890 at yahoo.com
> > >:
> >
> > I still hear a slight echo of my voice when I talk with
> > somone out the PSTN. The voice on the other end sounds
> > very choppy and a little distorted. When I talk to other
> > people within our office, the sound is perfect.Can some
> > help?
> >
> > We are all using:
> >
> > Polycom 501 <--> asterisk <--> PSTN
> >
> > zapata.conf:
> > [channels]
> > group = 1
> > language=en
> > context=incoming
> & gt; signalling=fxs_ks
> > switchtype=national
> > usecallerid=yes
> > hidecallerid=no
> > callwaiting=yes
> > musiconhold=default
> > usecallingpres=yes
> > callwaitingcallerid=yes
> > threewaycalling=yes
> > transfer=yes
> > canpark=yes
> > cancallforward=yes
> > callreturn=yes
> > echocancel=yes
> > echotraining=yes
> > echocancelwhenbridged=yes
> > rxgain=10.0
> > txgain=10.0
> > channel => 1-4
> >
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
> ------------------------------------------------------------------------
> Yahoo! Mail
> Use Photomail
> <http://pa.yahoo.com/*http://us.rd.yahoo.com/evt=38867/*http://photomail.mail.yahoo.com>
> to share photos without annoying attachments.
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
--
Mojo <mojo at horanappraisals.com>
Office Manger, Horan & Company, LLC
(907) 747-6666 x112
More information about the asterisk-users
mailing list