[Asterisk-Users] Problem getting two x200p cards working on 1.2.4

[Mojo with Horan & Company, LLC]

forgot to add this -- after the change in zaptel.conf, you would want to 
put a "channel => 2" in zapata.conf right after the "channel => 1" at 
the bottom.

Now asterisk can actually see it.

Guillermo Salas M wrote:
> Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp
>  kernel. 
> 
> I've two x100p cards connected, only one card is reconigzed by asterisk.
> 
> 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
> Modem/ISDN interface
> 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
> compatible 10/100 Ethernet (rev 31)
> 02:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
> Modem/ISDN interface
> 
> This is the cli output for zap show channels :
> 
> My /etc/zaptel.conf :
> 
> # Zaptel Configuration File
> #
> # This file is parsed by the Zaptel Configurator, ztcfg
> #
> 
> # It must be in the module loading order
> 
> 
> # Span 1: WCFXO/1 "Generic Clone Board 2"
> fxsks=1
> 
> # Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"
> 
> # Global data
> 
> loadzone        = us
> defaultzone     = us
> 
> 
> My /etc/asterisk/zapata-auto.conf
> 
> ; Zaptel Channels Configurations (zapata.conf)
> ;
> ; This is not intended to be a complete zapata.conf. Rather, it is
> intended
> ; to be #include-d by /etc/zapata.conf that will include the global
> settings
> ;
> callerid=asreceived
> 
> ; Span 1: WCFXO/1 "Generic Clone Board 2"
> signalling=fxs_ks
> ; Note: this is a trunk. Create a ZAP trunk in AMP for Channel 1
> context=from-pstn
> group=0
> channel => 1
> 
> 
> ; Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"
> 
> 
> This is the corresponding 'lspci -vv -n' for my two cards:
> 
> 02:01.0 Class 0780: e159:0001
>         Subsystem: 8086:0003
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (250ns min, 32000ns max)
>         Interrupt: pin A routed to IRQ 201
>         Region 0: I/O ports at b800 [size=256]
>         Region 1: Memory at feaff000 (32-bit, non-prefetchable)
> [size=4K]
>         Capabilities: [40] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0
> +,D1-,D2+,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 
> 02:03.0 Class 0780: e159:0001
>         Subsystem: 8086:0003
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (250ns min, 32000ns max)
>         Interrupt: pin A routed to IRQ 177
>         Region 0: I/O ports at b000 [size=256]
>         Region 1: Memory at feafd000 (32-bit, non-prefetchable)
> [size=4K]
>         Capabilities: [40] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0
> +,D1-,D2+,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 
> 
> And dmesg shows:
> 
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device c0340020(lo)
> IPv6 over IPv4 tunneling driver
> divert: not allocating divert_blk for non-ethernet device sit0
> eth0: no IPv6 routers present
> Freed a Wildcard
> Unregistered Tormenta2
> Zapata Telephony Interface Unloaded
> Zapata Telephony Interface Registered on major 196
> Zaptel Version:  Echo Canceller: KB1
> Registered Tormenta2 PCI
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 201
> Failed to initailize DAA, giving up...
> wcfxo: probe of 0000:02:01.0 failed with error -5
> ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 177
> wcfxo: DAA mode is 'FCC'
> Found a Wildcard FXO: Generic Clone
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> 
> 
> Any ideas?
> 

-- 
Mojo <mojo at horanappraisals.com>
Office Manger, Horan & Company, LLC
(907) 747-6666 x112