[Asterisk-Users] Very bad quality with AVM Fritz!card PCI and chan_capi

[Benjamin Sebbah]

----- Original Message -----
From: Armin Schindler <armin at melware.de>
Date: Thursday, June 29, 2006 11:48 am
Subject: Re: [Asterisk-Users] Very bad quality with AVM Fritz!card PCI
and chan_capi

> On Thu, 29 Jun 2006, Benjamin Sebbah wrote:
> > Hi everyone,
> > 
> > I have Asterisk SVN-trunk-r7498 running for a few months and I'm 
> quite> happy with it. However, I am experiencing a quality issue 
> with my AVM
> > Fritz!card PCI which is used with chan_capi. When somebody calls 
> me on
> > this line he hears a lot of noise and I hear "scratches" and 
> "plops". It
> > is very annoying. Below is is my /etc/asterisk/capi.conf 
> > I've tried to play with echotail and echosquelch but the quality is
> > always terrible. 
> > 
> > Any suggestion is welcomed.
> 
> echotail is for hardare-echo-cancel only (e.g. Eicon Diva Server) 
> and does 
> not change anything for AVM card.
> Did you try to disable echosquelch?
> 
> Why did you set rx/txgain to 0.5 ? Most people use 0.8, but I use 
> no gain by setting it to 1.0, which works here good.
> 
> Armin

Thanks for the answer, I did try to disable equosquelch but it doesn't
change anything (by the way it is disabled right now). To see if the
noise was a gain issue I tried to modify rx/txgain to see if it changed
anything but it didn't so I let those two values at 0.5

Any other idea?

Ben





> 
> > Thanks,
> > 
> > Ben
> > 
> > </etc/asterisk/capi.conf>
> > [general]
> > rxgain=0.5
> > txgain=0.5
> > language=fr      ;set default language
> > ;ulaw=yes        ;set this, if you live in u-law world instead of 
> a-law
> > [ISDN1]
> > 
> > isdnmode=DID     ;'MSN' (point-to-multipoint) or 'DID' (direct 
> inward dial)
> >                  ;when using NT-mode, 'DID' should be set in any 
> case> incomingmsn=*    ;allow incoming calls to this list of 
> MSNs/DIDs, * = any
> > controller=1     ;capi controller number to use
> > group=9          ;dialout group
> > softdtmf=on      ;enable/disable software dtmf detection, 
> recommended> for AVM cards
> > relaxdtmf=on     ;in addition to softdtmf, you can use relaxed dtmf
> > detection
> > accountcode=     ;Asterisk accountcode to use in CDRs
> > context=capi-in  ;context for incoming calls
> > ;echosquelch=2   ;_VERY_PRIMITIVE_ echo suppression
> > echocancel=yes  ;EICON DIVA SERVER (CAPI) echo cancelation
> >                  ;(possible values: 'no', 'yes', 'force', 'g164', 
> 'g165')> echocancelold=no ;use facility selector 6 instead of 
> correct 8
> > (necessary for older eicon drivers)
> > echotail=128     ;echo cancel tail setting
> > devices=2        ;number of concurrent calls on this controller
> >                  ;(2 makes sense for single BRI, 30 for PRI)
> > 
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> > 
> > Asterisk-Users mailing list
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
> > 
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>