[Asterisk-Users] BN8S0 problem - Extension can never match, so disconnecting

[nik600]

hi

i've configured a Beronet BN8S0 Card with misdn beronet utility.

the card is configured with all lines in TE and P2P mode, and it is
connected with the special cable with an ISDN connection.

i've turned on debugging to level 4, this is the output from the
asterisk cli when i receive a call:


P[ 5] MGMT: Short status dinfo 1000001
P[ 5] MGMT: SSTATUS: L1_ACTIVATED
P[ 5] handle_frm: frm->addr:42000503 frm->prim:3f082
P[ 5] handle_frm: frm->addr:42000503 frm->prim:30582
P[ 5] set_channel: bc->channel:0 channel:1
P[ 5] I IND :SETUP oad:4656708 dad:465670127
P[ 5]  --> mode:TE cause:16 ocause:16 rad: cad:
P[ 5]  --> facility:FAC_NONE out_facility:FAC_NONE
P[ 5]  --> info_dad: onumplan:2 dnumplan:2 rnumplan:  cpnnumplan:0
P[ 5]  --> screen:0 --> pres:0
P[ 5]  --> channel:1 caps:Speech pi:0 keypad:
P[ 5]  --> urate:0 rate:16 mode:0 user1:0
P[ 5]  --> pid:0 addr:0 l3id:a0001
P[ 5]  --> b_stid:0 layer_id:0
P[ 5]  --> bc:821d7ac h:0 sh:0
P[ 5]  --> bc_state:BCHAN_CLEANED
P[ 5]  --> Bearer: Speech
P[ 5]  --> Codec: Alaw
P[ 0]  --> * NEW CHANNEL dad:465670127 oad:4656708
P[ 5]  --> CTON: Unknown
P[ 5] * Queuing chan 0x8285bf0
Jun  8 19:32:29 WARNING[5019]: chan_misdn.c:4390 chan_misdn_log:
Extension can never match, so disconnecting
P[ 5] Tone Indicate:
P[ 5]  --> Busy
P[ 5] misdn_write: zero write
P[ 5] I SEND:RELEASE oad:04656708 dad:0465670127
P[ 5]  --> bc_state:BCHAN_CLEANED
P[ 5]  --> mode:TE cause:16 ocause:1 rad: cad:
P[ 5]  --> facility:FAC_NONE out_facility:FAC_NONE
P[ 5]  --> info_dad: onumplan:2 dnumplan:2 rnumplan:  cpnnumplan:0
P[ 5]  --> screen:0 --> pres:0
P[ 5]  --> channel:1 caps:Speech pi:0 keypad:
P[ 5]  --> urate:0 rate:16 mode:0 user1:0
P[ 5]  --> pid:0 addr:0 l3id:a0001
P[ 5]  --> b_stid:0 layer_id:0
P[ 5]  --> bc:821d7ac h:0 sh:0
P[ 5] P[ 5] Sending msg, prim:34d80 addr:0 dinfo:a0001
GOT SETUP OK
P[ 5] MGMT: Short status dinfo 2000001
P[ 5] MGMT: SSTATUS: L2_ESTABLISH
P[ 5] handle_frm: frm->addr:42000503 frm->prim:35a82
P[ 5] I IND :RELEASE_COMPLETE oad:04656708 dad:0465670127
P[ 5]  --> mode:TE cause:-1 ocause:1 rad: cad:
P[ 5]  --> facility:FAC_NONE out_facility:FAC_NONE
P[ 5]  --> info_dad: onumplan:2 dnumplan:2 rnumplan:  cpnnumplan:0
P[ 5]  --> screen:0 --> pres:0
P[ 5]  --> channel:1 caps:Speech pi:0 keypad:
P[ 5]  --> urate:0 rate:16 mode:0 user1:0
P[ 5]  --> pid:0 addr:0 l3id:a0001
P[ 5]  --> b_stid:0 layer_id:0
P[ 5]  --> bc:821d7ac h:0 sh:0
P[ 5]  --> bc_state:BCHAN_CLEANED
P[ 5] bchan_deactivate: called but not activated
P[ 5] release_chan: bc with l3id: a0001
P[ 5] * RELEASING CHANNEL pid:0 ctx:from-pstn dad:0465670127
oad:04656708 state: EXTCANTMATCH
P[ 5]  --> * State Down
P[ 5]  --> Setting AST State to down
P[ 5]  --> * State Wait4dig | ExtCantMatch
P[ 5] handle_frm: frm->addr:42000503 frm->prim:3f182
P[ 5]  --> lib: RELEASE_CR Ind with l3id:a0001
P[ 5]  --> lib: CLEANING UP l3id: a0001
P[ 5]  --> empty chan 1
P[ 5] BC_STATE_CHANGE: from:BCHAN_CLEANED to:BCHAN_EMPTY
P[ 5] BC_NEXT_STATE_CHANGE: from:BCHAN_EMPTY to:BCHAN_EMPTY
P[ 0] $$$ CLEANUP CALLED
P[ 5] $$$ CLEARING STACK
P[ 5] BC_STATE_CHANGE: from:BCHAN_EMPTY to:BCHAN_CLEANED
P[ 5] I IND :CLEAN_UP oad: dad:
P[ 5]  --> mode:TE cause:16 ocause:16 rad: cad:
P[ 5]  --> facility:FAC_NONE out_facility:FAC_NONE
P[ 5]  --> info_dad: onumplan:0 dnumplan:0 rnumplan:0 cpnnumplan:0
P[ 5]  --> screen:0 --> pres:0
P[ 5]  --> channel:0 caps:Speech pi:0 keypad:
P[ 5]  --> urate:0 rate:16 mode:0 user1:0
P[ 5]  --> pid:0 addr:0 l3id:a0001
P[ 5]  --> b_stid:0 layer_id:0
P[ 5]  --> bc:821d7ac h:0 sh:0
P[ 5]  --> bc_state:BCHAN_CLEANED
P[ 0] MGMT: DELLAYER|CONFIRM Addr: 1000000 !

can you help me to guess the problem?

in the file extension.conf i've got:

exten => 465670127,1,Dial(SIP/200)

where am i wrong?

thanks