[Asterisk-Users] BN8S0 Installation problem - 0 devices registrered

[Christophorus Laube]

You may also have a look at 
http://www.voip-info.org/wiki/view/Asterisk+mISDN+channels
> thanks to your reply
> using slackware the precompiled kernel is of the 2.4 series.
>
> I've also tried to remove all modules of my 2.6 kernel, download it ,
> configure it and boot it.
> Then, using a new 2.6.16.18 kernel (and working) i've run the make
> install of the beronet utility, but i'm still getting the same error.
>
> :-(
>
> Beronet has a support forum or support mailing list?
>
> >From their website it seems that the support is a payed service...
>
> hi and thanks
>
> On 6/3/06, Christophorus Laube <bob at semanticedge.de> wrote:
> > Do you still have the precompiled kernel installed? Try to boot to it.
> > Install kernel sources and try to rerun the install-misdn-mqueue script.
> > This is doing the needed stuff for you. Maybe the recompilation of your
> > kernel caused the problem. I have installed three systems with misdn the
> > last two months (two of them with the BN8S0) and I did not have problems
> > in that with the vendor delivered precompiled kernel. To not need to
> > recompile the kernel is one of the reasons they build the misdn in a
> > kernel and a user space part. You can also contact beronet in order to
> > get some support. They support their cards until they are correctly
> > recognized in asterisk.
> >
> > Cheers
> >
> > > thanks to your reply
> > >
> > > i've also tried to use install-misdn-mqueue but:
> > >
> > > root at testing_asterisk:/usr/src/install-misdn-mqueue#
> > > /etc/init.d/misdn-init scan [OK] found the following devices:
> > > card=1,0x8
> > > [ii] run "/etc/init.d/misdn-init config" to store this information to
> > > /etc/misdn-init.conf
> > >
> > > as you can see, the scan finish succesfully, but if try to start misd i
> > > get: root at testing_asterisk:/usr/src/install-misdn-mqueue#
> > > /etc/init.d/misdn-init start
> > > FATAL: Module capi not found.
> > > FATAL: Error inserting mISDN_capi
> > > (/lib/modules/2.6.16.18/extra/mISDN_capi.ko): Unknown symbol in
> > > module, or unknown parameter (see dmesg)
> > > -----------------------------------------
> > >  Loading module(s) for your misdn-cards:
> > > -----------------------------------------
> > > modprobe --ignore-install hfcmulti type=0x8
> > > protocol=0x2,0x2,0x2,0x2,0x2,0x2,0x2,0x2
> > > layermask=0xf,0xf,0xf,0xf,0xf,0xf,0xf,0xf poll=128 debug=0
> > >
> > >
> > > and dmesg:
> > > Modular ISDN Stack core $Revision: 1.34 $
> > > mISDNd: kernel daemon started
> > > ISDN L1 driver version 1.16
> > > ISDN L2 driver version 1.27
> > > mISDN: DSS1 Rev. 1.38
> > > mISDN_dsp: Audio DSP  Rev. 1.17 (debug=0x0) EchoCancellor MG2
> > > mISDN_dsp: DSP clocks every 64 samples. This equals 2 jiffies.
> > > mISDN_capi: Unknown symbol capi_cmd2str
> > > mISDN_capi: Unknown symbol capi_cmsg_header
> > > mISDN_capi: Unknown symbol detach_capi_ctr
> > > mISDN_capi: Unknown symbol capi_cmsg2message
> > > mISDN_capi: Unknown symbol capi_ctr_reseted
> > > mISDN_capi: Unknown symbol capi_ctr_ready
> > > mISDN_capi: Unknown symbol capi_message2cmsg
> > > mISDN_capi: Unknown symbol capi_ctr_handle_message
> > > mISDN_capi: Unknown symbol attach_capi_ctr
> > > mISDNd: test event done
> > > mISDN: HFC-multi driver Rev. 1.41
> > > 0 devices registered
> > >
> > > finally, if i try to start asterisk:
> > >
> > >  [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri))
> > > mISDN_close: fid(18) isize(131072) inbuf(0xb7580008) irp(0xb7580008)
> > > iend(0xb7580008)
> > > Jun  3 08:42:31 ERROR[8296]: chan_misdn.c:3775 load_module: Unable to
> > > initialize mISDN
> > > Jun  3 08:42:31 WARNING[8296]: loader.c:414 __load_resource:
> > > chan_misdn.so: load_module failed, returning -1
> > > Jun  3 08:42:31 WARNING[8296]: loader.c:554 load_modules: Loading
> > > module chan_misdn.so failed!
> > > _______________________________________________
> > > --Bandwidth and Colocation provided by Easynews.com --
> > >
> > > Asterisk-Users mailing list
> > > To UNSUBSCRIBE or update options visit:
> > >    http://lists.digium.com/mailman/listinfo/asterisk-users
> >
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> >
> > Asterisk-Users mailing list
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users