[Asterisk-Users] TE410P E1 Red Alarm
Olivier Perrin
o.perrin at kosmos-telecom.fr
Thu Jan 5 08:04:50 MST 2006
Hi,
You could only take timing from one E1 per card. So you should use :
span=1,1,0,ccs,hdb3,crc4
span=2,0,0,ccs,hdb3,crc4
span=3,0,0,ccs,hdb3,crc4
span=4,0,0,ccs,hdb3,crc4
instead of :
span=1,1,0,ccs,hdb3,crc4
span=2,1,0,ccs,hdb3,crc4
span=3,1,0,ccs,hdb3,crc4
span=4,1,0,ccs,hdb3,crc4
Le dimanche 25 décembre 2005 à 03:07 -0600, Diyanat Ali a écrit :
> Hello!
>
> I have a TE410P quad span card with 4 E1, i am using asterisk 1.2.1, i was
> using it without any issues earlier with just 1 E1 on span 1 and i recently
> plugged in 3 more E1's, only span 1 is working, the e1 for span 1 is from a
> different provider then the rest, the settings are same for both, but i
> constantly get red alaram on the span 2,3,4, i tried all settings, including
> the timming source , framing, coding , signalling type etc, without any
> sucesss
>
> what maybe the cause of the red alarm
>
> Regards
>
> Diyanat
>
> lspci -vvv
> 06:01.0 Communication controller: Unknown device d161:0410 (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Interrupt: pin A routed to IRQ 74
> Region 0: Memory at fdff0000 (32-bit, non-prefetchable) [size=128]
>
> lsmod
> Module Size Used by Not tainted
> wct4xxp 78432 124
> zaptel 183776 250 [wct4xxp]
>
>
>
> cat /proc/zaptel/*
> Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4
> 1 TE4/0/1/1 Clear (In use) .... upto
> 16 TE4/0/1/16 HDLCFCS (In use) .... upto
> 31 TE4/0/1/31 Clear (In use)
> Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS/CRC4 RED
> 32 TE4/0/2/1 Clear (In use) .... upto
> 47 TE4/0/2/16 HDLCFCS (In use) .... upto
> 62 TE4/0/2/31 Clear (In use)
> Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" HDB3/CCS/CRC4 RED
> 63 TE4/0/3/1 Clear (In use) .... upto
> 78 TE4/0/3/16 HDLCFCS (In use) .... upto
> 93 TE4/0/3/31 Clear (In use)
> Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4" HDB3/CCS/CRC4 RED
> 94 TE4/0/4/1 Clear (In use) .... upto
> 109 TE4/0/4/16 HDLCFCS (In use) .... upto
> 124 TE4/0/4/31 Clear (In use)
>
>
> ztcfg -v
> SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
> SPAN 2: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
> SPAN 3: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
> SPAN 4: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
> 124 channels configured.
>
> zttool
> Alarms Span
> OK T4XXP (PCI) Card 0 Span 1
> RED T4XXP (PCI) Card 0 Span 2
> RED T4XXP (PCI) Card 0 Span 3
> RED T4XXP (PCI) Card 0 Span 4
>
> CLI> zap show status
> Description Alarms IRQ bpviol
> CRC4
> T4XXP (PCI) Card 0 Span 1 OK 0 0 0
> T4XXP (PCI) Card 0 Span 2 RED 0 0 0
> T4XXP (PCI) Card 0 Span 3 RED 0 0 0
> T4XXP (PCI) Card 0 Span 4 RED 0 0 0
>
>
>
> alpha*CLI> pri show span 1
> Primary D-channel: 16
> Status: Provisioned, Up, Active
> Switchtype: EuroISDN
> Type: CPE
> Window Length: 0/7
> Sentrej: 0
> SolicitFbit: 0
> Retrans: 0
> Busy: 0
> Overlap Dial: 0
> T200 Timer: 1000
> T203 Timer: 10000
> T305 Timer: 30000
> T308 Timer: 4000
> T313 Timer: 4000
> N200 Counter: 3
>
>
> alpha*CLI> pri show span 2
> Primary D-channel: 47
> Status: Provisioned, In Alarm, Down, Active
> Switchtype: EuroISDN
> Type: CPE
> Window Length: 0/7
> Sentrej: 0
> SolicitFbit: 0
> Retrans: 0
> Busy: 0
> Overlap Dial: 0
> T200 Timer: 1000
> T203 Timer: 10000
> T305 Timer: 30000
> T308 Timer: 4000
> T313 Timer: 4000
> N200 Counter: 3
> its the same as span for the rest as upto span 4
>
>
> CLI>pri intense debug span 2
> >Unnumbered frame:
> >SAPI: 00 C/R: 0 EA: 0
> > TEI: 000 EA: 1
> > M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode
> >extended) ]
> >0 bytes of data
> Sending Set Asynchronous Balanced Mode Extended
>
> same for the rest
>
>
> zaptel.conf
> span=1,1,0,ccs,hdb3,crc4
> bchan = 1-15
> dchan = 16
> bchan = 17-31
> span=2,1,0,ccs,hdb3,crc4
> bchan = 32-46
> dchan = 47
> bchan = 48-62
> span=3,1,0,ccs,hdb3,crc4
> bchan = 63-77
> dchan = 78
> bchan = 79-93
> span=4,1,0,ccs,hdb3,crc4
> bchan = 94-108
> dchan = 109
> bchan = 110-124
> loadzone=se
> defaultzone=se
>
>
>
> zapata.conf
> [channels]
> language=us
> context=sip
> switchtype=euroisdn
> pridialplan=unknown
> prilocaldialplan=unknown
> signalling=pri_cpe
> usecallerid=yes
> hidecallerid=no
> callwaiting=yes
> usecallingpres=yes
> callwaitingcallerid=yes
> threewaycalling=yes
> transfer=yes
> cancallforward=yes
> callreturn=yes
> echocancel=yes
> echocancelwhenbridged=yes
> echotraining=yes
> cidsignalling=dtmf
> cidstart=ring
> rxgain=0.0
> txgain=0.0
> group=1
> callgroup=1
> pickupgroup=1
> immediate=no
> callerid=asreceived
>
> group=1
> channel => 1-15
> channel => 17-31
>
> group=2
> channel => 32-46
> channel => 48-62
>
> group=3
> channel => 63-77
> channel => 79-93
>
> group=4
> channel => 94-108
> channel => 110-124
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
More information about the asterisk-users
mailing list