[Asterisk-Users] Problem making outbound calls on TE210P using NFAS

Thu Feb 16 09:21:44 MST 2006

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Why do you have immediate set?

*immediate*: Normally (i.e. with immediate set to 'no', the default),
when you lift an FXS handset, the Zaptel driver provides you a
dialtone and listens for digits that you dial, passing them on to
Asterisk. Asterisk waits until the number you've dialed matches an
extension, and then begins executing the first command on the matching
extension. If you set immediate=yes, then Asterisk will instruct the
Zaptel driver to not generate a dialtone when you lift a handset,
instead passing control immediately to Asterisk. Asterisk will start
executing the commands for this channel's "s" extension
<http://www.voip-info.org/wiki/index.php?page=Asterisk+s+extension>.
This is sometimes referred to as "batphone mode". Default: no.
   immediate=yes

Aldo Gonzalez wrote:

> Hello,
>
> I'm running Asterisk at home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri
> 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P
>
> I have 2 t1 circuits using NFAS with dchan on 24 and no backup
> dchan. I am able to receive inbound calls on all channels and can
> only make outbound calls on channels 25-48. Attempting to make an
> outbound call on channels 1-23 results in congestion.
>
> ---------------------------
>
> [/etc/zaptel.conf] # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"
> B8ZS/ESF ClockSource # ??: 1 TE2/0/1/1 Clear # ??: 2 TE2/0/1/2
> Clear # ??: 3 TE2/0/1/3 Clear # ??: 4 TE2/0/1/4 Clear # ??: 5
> TE2/0/1/5 Clear # ??: 6 TE2/0/1/6 Clear # ??: 7 TE2/0/1/7 Clear #
> ??: 8 TE2/0/1/8 Clear # ??: 9 TE2/0/1/9 Clear # ??: 10 TE2/0/1/10
> Clear # ??: 11 TE2/0/1/11 Clear # ??: 12 TE2/0/1/12 Clear # ??: 13
> TE2/0/1/13 Clear # ??: 14 TE2/0/1/14 Clear # ??: 15 TE2/0/1/15
> Clear # ??: 16 TE2/0/1/16 Clear # ??: 17 TE2/0/1/17 Clear # ??: 18
> TE2/0/1/18 Clear # ??: 19 TE2/0/1/19 Clear # ??: 20 TE2/0/1/20
> Clear # ??: 21 TE2/0/1/21 Clear # ??: 22 TE2/0/1/22 Clear # ??: 23
> TE2/0/1/23 Clear # ??: 24 TE2/0/1/24 HDLCFCS
>
> # Span 2: TE2/0/2 "T2XXP (PCI) Card 0 Span 2" B8ZS/ESF # ??: 25
> TE2/0/2/1 Clear # ??: 26 TE2/0/2/2 Clear # ??: 27 TE2/0/2/3 Clear #
> ??: 28 TE2/0/2/4 Clear # ??: 29 TE2/0/2/5 Clear # ??: 30 TE2/0/2/6
> Clear # ??: 31 TE2/0/2/7 Clear # ??: 32 TE2/0/2/8 Clear # ??: 33
> TE2/0/2/9 Clear # ??: 34 TE2/0/2/10 Clear # ??: 35 TE2/0/2/11 Clear
> # ??: 36 TE2/0/2/12 Clear # ??: 37 TE2/0/2/13 Clear # ??: 38
> TE2/0/2/14 Clear # ??: 39 TE2/0/2/15 Clear # ??: 40 TE2/0/2/16
> Clear # ??: 41 TE2/0/2/17 Clear # ??: 42 TE2/0/2/18 Clear # ??: 43
> TE2/0/2/19 Clear # ??: 44 TE2/0/2/20 Clear # ??: 45 TE2/0/2/21
> Clear # ??: 46 TE2/0/2/22 Clear # ??: 47 TE2/0/2/23 Clear # ??: 48
> TE2/0/2/24 Clear
>
> span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs
>
> bchan=1-23,25-48 dchan=24
>
> loadzone = us defaultzone = us
>
> --------------------------- [/etc/asterisk/zapata.conf]
> [trunkgroups] trunkgroup=>1,24 spanmap => 1,1,1 spanmap => 2,1,2
> [channels] language=en context=from-pstn group=1 signalling=pri_cpe
> ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=5ess
> pridialplan=national callerid=asreceived under
> ;usedistinctiveringdetection=yes rxwink=300 ; Atlas
> seems to use long (250ms) winks usecallerid=yes hidecallerid=no
> callwaiting=yes usecallingpres=yes callwaitingcallerid=yes
> threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes
> echocancel=yes echocancelwhenbridged=yes ; default - no
> echotraining=400 ; default 800 rxgain=0.0 txgain=0.0 callgroup=1
> pickupgroup=1 immediate=yes channel => 1-23,25-48 #include
> zapata-auto.conf #include zapata_additional.conf
>
> --------------------------- [/etc/sysconfig/zaptel]
> MODULES="$MODULES wct2xxp"
>
> ---------------------------
>
> Below is a snippet of /var/log/asterisk/full when attempting to
> make outbound call via lower channels:
>
>
> Feb 16 10:41:34 VERBOSE[3878] logger.c: -- Executing
> GotoIf("SIP/2002-2290", "0?16") in new stack Feb 16 10:41:34
> DEBUG[3878] pbx.c: Not taking any branch Feb 16 10:41:34
> VERBOSE[3878] logger.c: -- Executing Dial("SIP/2002- 2290",
> "ZAP/g1/xxxxxxxxxx") in new stack Feb 16 10:41:34 VERBOSE[3878]
> logger.c: -- Requested transfer capability: 0x00 - SPEECH Feb
> 16 10:41:34 VERBOSE[3878] logger.c: -- Called g1/xxxxxxxxxx Feb
> 16 10:41:35 VERBOSE[3368] logger.c: -- Channel 1/2, span 1 got
> hangup Feb 16 10:41:35 VERBOSE[3878] logger.c: -- Zap/2-1 is
> circuit-busy Feb 16 10:41:35 DEBUG[3878] chan_zap.c: Set option
> AUDIO MODE, value: ON(1) on Zap/2-1 Feb 16 10:41:35 DEBUG[3878]
> chan_zap.c: Hangup: channel: 2 index = 0, normal = 15, callwait =
> -1, thirdcall = -1 Feb 16 10:41:35 DEBUG[3878] chan_zap.c: Already
> hungup... Calling hangup once, and clearing call Feb 16 10:41:35
> DEBUG[3878] chan_zap.c: disabled echo cancellation on channel 2 Feb
> 16 10:41:35 DEBUG[3878] chan_zap.c: Set option TDD MODE, value:
> OFF(0) on Zap/2-1 Feb 16 10:41:35 DEBUG[3878] chan_zap.c: Updated
> conferencing on 2, with 0 conference users Feb 16 10:41:35
> DEBUG[3878] chan_zap.c: Set option AUDIO MODE, value: OFF(0) on
> Zap/2-1 Feb 16 10:41:35 DEBUG[3878] chan_zap.c: disabled echo
> cancellation on channel 2 Feb 16 10:41:35 VERBOSE[3878] logger.c:
> -- Hungup 'Zap/2-1' Feb 16 10:41:35 VERBOSE[3878] logger.c: ==
> Everyone is busy/congested at this time (1:0/1/0) Feb 16 10:41:35
> DEBUG[3878] app_dial.c: Exiting with DIALSTATUS=CONGESTION.
>
> where xxxxxxxxxx is a phone number
>
> ---------------------------
>
> Enabling CLI> pri intense debug span 1 -- Executing
> Dial("SIP/2002-8576", "ZAP/g1/18009993355") in new stack --
> Requested transfer capability: 0x00 - SPEECH
>
>> [ 00 01 ce d2 08 02 00 07 05 04 03 80 90 a2 18 04 e9 81 83 82 6c
>> 0c 21 80 38 30 30 34 35 36 32
>
> 30 39 39 70 0c a1 31 38 30 30 39 39 39 33 33 35 35 ]
>
>> Informational frame: SAPI: 00 C/R: 0 EA: 0 TEI: 000 EA: 1
>> N(S): 103 0: 0 N(R): 105 P: 0 44 bytes of data
>
> -- Restarting T203 counter Stopping T_203 timer Starting T_200
> timer
>
>> Protocol Discriminator: Q.931 (8) len=44 Call Ref: len= 2
>> (reference 7/0x7) (Originator) Message type: SETUP (5) [04 03 80
>> 90 a2] Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info
>> transfer capability: Speech (0) Ext: 1 Trans mode/rate: 64kbps,
>> circuit-mode (16) Ext: 1 User information layer 1: u-Law (34)
>> [18 04 e9 81 83 82] Channel ID (len= 6) [ Ext: 1 IntID:
>> Explicit, PRI Spare: 0, Exclusive Dchan: 0 ChanSel: Reserved Ext:
>> 1 DS1 Identifier: 1 Ext: 1 Coding: 0 Number Specified
>> Channel Type: 3 Ext: 1 Channel: 2 ] [6c 0c 21 80 38 30 30 34 35
>> 36 32 30 39 39] Calling Number (len=14) [ Ext: 0 TON: National
>> Number (2) NPI: ISDN/Telephony Numbering Plan
>
> (E.164/E.163) (1)
>
>> Presentation: Presentation permitted, user number not screened
>
> (0) '8004562099' ]
>
>> [70 0c a1 31 38 30 30 39 39 39 33 33 35 35] Called Number
>> (len=14) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony
>> Numbering Plan
>
> (E.164/E.163) (1) '18009993355' ] asterisk1*CLI> < [ 00 01 01 d0 ]
>
> < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000
> EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 104
> P/F: 0 < 0 bytes of data -- ACKing all packets from 102 to (but not
> including) 104 -- ACKing packet 103, new txqueue is -1 (-1 means
> empty) -- Since there was nothing left, stopping T200 counter --
> Nothing left, starting T203 counter -- Restarting T203 counter
>
> < [ 02 01 d2 d0 08 02 80 07 5a 08 02 80 a2 ]
>
> < Informational frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000
> EA: 1 < N(S): 105 0: 0 < N(R): 104 P: 0 < 9 bytes of data --
> ACKing all packets from 103 to (but not including) 104 -- Since
> there was nothing left, stopping T200 counter -- Stopping T203
> counter since we got an ACK -- Nothing left, starting T203 counter
> < Protocol Discriminator: Q.931 (8) len=9 < Call Ref: len= 2
> (reference 7/0x7) (Terminator) < Message type: RELEASE COMPLETE
> (90) < [08 02 80 a2] < Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU)
> standard (0) 0: 0 Location: User (0) < Ext: 1
> Cause: Unknown (34), class = Network Congestion (2) ] Sending
> Receiver Ready (106)
>
>> [ 02 01 01 d4 ]
>
>
>> Supervisory frame: SAPI: 00 C/R: 1 EA: 0 TEI: 000 EA: 1
>> Zero: 0 S: 0 01: 1 [ RR (receive ready) ] N(R): 106 P/F: 0 0
>> bytes of data
>
> -- Restarting T203 counter -- Restarting T203 counter -- Channel
> 1/2, span 1 got hangup -- Called g1/18009993355 -- Zap/2-1 is
> circuit-busy -- Hungup 'Zap/2-1' == Everyone is busy/congested at
> this time (1:0/1/0) -- Executing Goto("SIP/2002-8576",
> "s-CONGESTION|1") in new stack -- Goto
> (macro-dialout-trunk,s-CONGESTION,1) -- Executing
> NoOp("SIP/2002-8576", "Dial failed due to CONGESTION") in new stack
> -- Executing Macro("SIP/2002-8576", "outisbusy") in new stack --
> Executing Playback("SIP/2002-8576", "all-circuits-busy-now") in new
> stack -- Playing 'all-circuits-busy-now' (language 'en') --
> Executing Playback("SIP/2002-8576", "pls-try-call-later") in new
> stack -- Playing 'pls-try-call-later' (language 'en') == Spawn
> extension (macro-outisbusy, s, 2) exited non-zero on
> 'SIP/2002-8576' in macro 'outisbusy' == Spawn extension
> (from-internal, 818009993355, 2) exited non-zero on 'SIP/2002-8576'
> -- Executing Macro("SIP/2002-8576", "hangupcall") in new stack --
> Executing ResetCDR("SIP/2002-8576", "w") in new stack -- Executing
> NoCDR("SIP/2002-8576", "") in new stack -- Executing
> Wait("SIP/2002-8576", "5") in new stack == Spawn extension
> (macro-hangupcall, s, 3) exited non-zero on 'SIP/2002-8576' in
> macro 'hangupcall' == Spawn extension (from-internal, h, 1) exited
> non-zero on 'SIP/2002-8576' T203 counter expired, sending RR and
> scheduling T203 again Sending Receiver Ready (106)
>
>> [ 00 01 01 d5 ]
>
>
>> Supervisory frame: SAPI: 00 C/R: 0 EA: 0 TEI: 000 EA: 1
>> Zero: 0 S: 0 01: 1 [ RR (receive ready) ] N(R): 106 P/F: 1 0
>> bytes of data
>
> -- Restarting T203 counter asterisk1*CLI> < [ 00 01 01 d1 ]
>
> < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000
> EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 104
> P/F: 1 < 0 bytes of data -- ACKing all packets from 103 to (but not
> including) 104
>
>
> Thanks in advance, Aldo
>
> _______________________________________________ --Bandwidth and
> Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (MingW32)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

iD8DBQFD9KaYy9wPyZpnL2URAl0cAJ4tYVqHtUMVHxKBAglcUSYTStRkyACeOQcA
tYclmb7lQ5dA+/NBQyHicHo=
=za6c
-----END PGP SIGNATURE-----