[Asterisk-Users] problems with PRI

[asterisk at frameweb.it]

Hi, I configured an asterisk box with 1
Digium Wildcard TE110P T1/E1 Card 0

I setup the jumper in e1 position.

my zaptel.conf :

defaultzone=it
loadzone=it

#gestione PRI

span=1,0,0,ccs,hdb3,crc4,yellow
bchan=1-15 # set this to 1-15,17-31 for E1
dchan=16 # set this to 16 for E1
bchan=17-31 # set this to 1-15,17-31 for E1
#

Asterisk starts correctly, I see th 30 channels.

Anyway I cannot put any call on the PSTN PRI Channel.

Actually I don't know
1) ccs or cas ?   my provider (Fastweb Italy) does not answer.....
2) ami or hdb3 ? same answer (no answer)
3) crc or not ? my provider says it does not matter

moreover : what is supposed to show the zttool utility ?
If I push "Loop" nothing happens.

If I run ztcfg -v i see

SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: Individual Clear channel (Default) (Slaves: 01)
Channel 02: Individual Clear channel (Default) (Slaves: 02)
Channel 03: Individual Clear channel (Default) (Slaves: 03)
Channel 04: Individual Clear channel (Default) (Slaves: 04)
Channel 05: Individual Clear channel (Default) (Slaves: 05)
Channel 06: Individual Clear channel (Default) (Slaves: 06)
Channel 07: Individual Clear channel (Default) (Slaves: 07)
Channel 08: Individual Clear channel (Default) (Slaves: 08)
Channel 09: Individual Clear channel (Default) (Slaves: 09)
Channel 10: Individual Clear channel (Default) (Slaves: 10)
Channel 11: Individual Clear channel (Default) (Slaves: 11)
Channel 12: Individual Clear channel (Default) (Slaves: 12)
Channel 13: Individual Clear channel (Default) (Slaves: 13)
Channel 14: Individual Clear channel (Default) (Slaves: 14)
Channel 15: Individual Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Individual Clear channel (Default) (Slaves: 17)
Channel 18: Individual Clear channel (Default) (Slaves: 18)
Channel 19: Individual Clear channel (Default) (Slaves: 19)
Channel 20: Individual Clear channel (Default) (Slaves: 20)
Channel 21: Individual Clear channel (Default) (Slaves: 21)
Channel 22: Individual Clear channel (Default) (Slaves: 22)
Channel 23: Individual Clear channel (Default) (Slaves: 23)
Channel 24: Individual Clear channel (Default) (Slaves: 24)
Channel 25: Individual Clear channel (Default) (Slaves: 25)
Channel 26: Individual Clear channel (Default) (Slaves: 26)
Channel 27: Individual Clear channel (Default) (Slaves: 27)
Channel 28: Individual Clear channel (Default) (Slaves: 28)
Channel 29: Individual Clear channel (Default) (Slaves: 29)
Channel 30: Individual Clear channel (Default) (Slaves: 30)
Channel 31: Individual Clear channel (Default) (Slaves: 31)

with asterisk turned off, zttool shows
     RED/NOP         Digium Wildcard TE110P T1/E1 Card 0

with asterisk turned on, zttool shows

 RED             Digium Wildcard TE110P T1/E1 Card 0

if i try
 cat /dev/zap/1
with asterisk turned off, I see a lot of raw  data incoming
with asterisk turned on, I see

cat: /dev/zap/1: Device or resource busy

same with all the othe channel , except control channel 16

If I try cat: /dev/zap/1 with asterisk turned off, i see.

cat: /dev/zap/1cat: No such file or directory
Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" HDB3/CCS/CRC4 RED
NOTOPEN

    1 WCT1/0/1 Clear
    2 WCT1/0/2 Clear
    3 WCT1/0/3 Clear
    4 WCT1/0/4 Clear
    5 WCT1/0/5 Clear
    6 WCT1/0/6 Clear
    7 WCT1/0/7 Clear
    8 WCT1/0/8 Clear
    9 WCT1/0/9 Clear
   10 WCT1/0/10 Clear
   11 WCT1/0/11 Clear
   12 WCT1/0/12 Clear
   13 WCT1/0/13 Clear
   14 WCT1/0/14 Clear
   15 WCT1/0/15 Clear
   16 WCT1/0/16 HDLCFCS
   17 WCT1/0/17 Clear
   18 WCT1/0/18 Clear
   19 WCT1/0/19 Clear
   20 WCT1/0/20 Clear
   21 WCT1/0/21 Clear
   22 WCT1/0/22 Clear
   23 WCT1/0/23 Clear
   24 WCT1/0/24 Clear
   25 WCT1/0/25 Clear
   26 WCT1/0/26 Clear
   27 WCT1/0/27 Clear
   28 WCT1/0/28 Clear
   29 WCT1/0/29 Clear
   30 WCT1/0/30 Clear
   31 WCT1/0/31 Clear

If I try cat: /dev/zap/1 with asterisk turned ON, i see.

cat: /dev/zap/1cat: No such file or directory
Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" HDB3/CCS/CRC4 RED

    1 WCT1/0/1 Clear (In use)
    2 WCT1/0/2 Clear (In use)
    3 WCT1/0/3 Clear (In use)
    4 WCT1/0/4 Clear (In use)
    5 WCT1/0/5 Clear (In use)
    6 WCT1/0/6 Clear (In use)
    7 WCT1/0/7 Clear (In use)
    8 WCT1/0/8 Clear (In use)
    9 WCT1/0/9 Clear (In use)
   10 WCT1/0/10 Clear (In use)
   11 WCT1/0/11 Clear (In use)
   12 WCT1/0/12 Clear (In use)
   13 WCT1/0/13 Clear (In use)
   14 WCT1/0/14 Clear (In use)
   15 WCT1/0/15 Clear (In use)
   16 WCT1/0/16 HDLCFCS (In use)
   17 WCT1/0/17 Clear (In use)
   18 WCT1/0/18 Clear (In use)
   19 WCT1/0/19 Clear (In use)
   20 WCT1/0/20 Clear (In use)
   21 WCT1/0/21 Clear (In use)
   22 WCT1/0/22 Clear (In use)
   23 WCT1/0/23 Clear (In use)
   24 WCT1/0/24 Clear (In use)
   25 WCT1/0/25 Clear (In use)
   26 WCT1/0/26 Clear (In use)
   27 WCT1/0/27 Clear (In use)
   28 WCT1/0/28 Clear (In use)
   29 WCT1/0/29 Clear (In use)
   30 WCT1/0/30 Clear (In use)
   31 WCT1/0/31 Clear (In use)
4 RED

Any help will be greatly appreciated,

thanks in advance,

Andrea


Chi ricevesse questa mail per errore e' gentilmente pregato di cancellarla.

Visitate il sito http://www.frameweb.it