[Asterisk-Users] Incoming calls via CAPI and AVM Fritz Card

[Joerg Lauer]

Hi,

I'm not really sure if this helps you, but as far as I remember, the 
diastring with chan_capi-cm-0.6 is not 
"CAPI/g1/0299546476:b${EXTEN},30,r" but 
"CAPI/g<group>/<destination>[/<params>]" or in your case 
"CAPI/g1/${EXTEN}/b,30,r".

To set your CallerPresentation, use the SetCallerPres() in your 
Dialplan, which is now used as the CLIP/CLIR.

Regards Jörg

Esteban Guana-Jarrin wrote:
> Can anyone please provide some help. I have installed an AVM fritz card 
> on an asterisk box (asterisk at home version 1.5). I have installed the 
> card driver and chan_capi-cm-0.6. According to the installations guide I 
> can now see that the CAPI channel in asterisk is up,
> 
> *CLI> capi info
> Contr1: 2 B channels total, 2 B channels free.
> 
> I set up a trunk and the dialstring includes the following,
> 
> CAPI/g1/0299546476:b${EXTEN},30,r
> 
> My capi.conf is,
> 
> [general]
> nationalprefix=0
> internationalprefix=00
> rxgain=0.8
> txgain=0.8
> ;ulaw=yes        ;set this, if you live in u-law world instead of a-law
> 
> ; interface sections ...
> 
> [ISDN1]          ;this example interface gets name 'ISDN1' and may be any
>                 ;name not starting with 'g' or 'contr'.
> ;ntmode=yes      ;if isdn card operates in nt mode, set this to yes
> isdnmode=msn     ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
>                 ;when using NT-mode, ptp should be set in any case
> incomingmsn=*    ;allow incoming calls to this list of MSNs/DIDs, * == any
> ;controller=0    ;ISDN4BSD default
> ;controller=7    ;ISDN4BSD USB default
> controller=1     ;capi controller number to use
> group=1          ;dialout group
> ;prefix=0        ;set a prefix to calling number on incoming calls
> softdtmf=on      ;enable/disable software dtmf detection, recommended 
> for AVM cards
> relaxdtmf=on     ;in addition to softdtmf, you can use relaxed dtmf 
> detection
> accountcode=     ;Asterisk accountcode to use in CDRs
> context=from-trunk
> ;context=capi-in  ;context for incoming calls
> holdtype=hold    ;when Asterisk puts the call on hold, ISDN HOLD will be 
> used. If
>                 ;set to 'local' (default value), no hold is done and 
> Asterisk may
>                 ;play MOH.
> ;immediate=yes   ;immediate start of pbx with extension 's' if no digits 
> were
>                 ;received on incoming call (no destination number yet)
> ;echosquelch=1   ;_VERY_PRIMITIVE_ echo suppression
> ;echocancel=yes  ;EICON DIVA SERVER (CAPI) echo cancelation
>                 ;(possible values: 'no', 'yes', 'force', 'g164', 'g165')
> echocancelold=yes;use facility selector 6 instead of correct 8 
> (necessary for older eicon drivers)
> ;echotail=64     ;echo cancel tail setting
> ;bridge=yes      ;native bridging (CAPI line interconnect) if available
> ;callgroup=1     ;Asterisk call group
> ;deflect=1234567 ;deflect incoming calls to 1234567 if all B channels 
> are busy
> devices=2        ;number of concurrent calls on this controller
>                 ;(2 makes sense for single BRI, 30 for PRI)
> 
> I can't see that a number is assigned to msn, but I read somewhere on 
> this list that for this latest version of chan_capi this is not required.
> 
> I connected the asterisk box to the ISDN line, which belongs to a Hunt 
> group with number as shown in the dialstring and when ringing that 
> number from an external line I do not get any tone and asterisk does not 
> log any indications of incoming calls via the CAPI channel
> 
> Can anyone please shed some light on what do I need to do in order to be 
> able to receive calls via this setup.
> 
> 
> Thanks in advance,
> 
> PolAUs
> 
> _________________________________________________________________
> SEEK: Over 80,000 jobs across all industries at Australia's #1 job 
> site.    http://ninemsn.seek.com.au?hotmail
> 
> _______________________________________________
> --Bandwidth and Colocation sponsored by Easynews.com --
> 
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users