[Asterisk-Users] x100p (FXO) not being seen by asterisk (is my bestguess) .

[Paul]

First I don't like the 6 line cord.  Use an rj11 2 wire cord, but watch the
crossover vrs straight on the old red and green.

Next the interrupt must be fixed.  Do this in the CMOS before you boot.  Go
to the PCI bus assignments and set the IRQ or go and disable the serial
ports thereby allowing irq 3 and 4 to be assigned.

:)
Paul



-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Mr. James W.
Laferriere
Sent: Wednesday, October 26, 2005 7:53 PM
To: asterisk-users at lists.digium.com
Subject: [Asterisk-Users] x100p (FXO) not being seen by asterisk (is my
bestguess) .

	Hello All ,  I installed a x100p clone device in a system .
	I pulled (Wed, 26 Oct 2005 early am) cvs & compiled & installed for
a 
	2.6 kernel .  We call this system 'test' .  This system is a HP
Vectra 
	with a 933MHZ processor .  Test has all the z* modules installed
(*1).
	and can see the x100p (ie *2) .  
	The other system has been operational for some time .  I have a
ata-186 
	responding to two numbers 21 & 22 .  I attached a 6 line cord
between 
	the ata-186 port 22 & the 'line' side of the x100p .  I have
configured 
	the 3 necessary files (*3) .  Now when I call 22 from an ipphone the

	x100p does not pickup the line .  All it does is ring .
	I have to be missing something here .  Tia ,  JimL

ps:	Here is one problem I have yet been unable to resolv .  I am unable
to 
	move the x100p to some other IRQ & at present it is sharing irq 9
with 
	the SMBus .  Anyone know how to work around this ?

00:1f.3 SMBus: Intel Corporation 82801AA SMBus (rev 02)
        Subsystem: Intel Corporation 82801AA SMBus
        Flags: medium devsel, IRQ 9
        I/O ports at 1810 [size=16]

01:02.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN

interface
        Subsystem: Unknown device 8085:0003
        Flags: bus master, medium devsel, latency 64, IRQ 9
        I/O ports at 2000 [size=256]
        Memory at ec100000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2

(*1)
# modprobe -vl
/lib/modules/2.6.13.2/misc/ztdynamic.ko
/lib/modules/2.6.13.2/misc/ztdummy.ko
/lib/modules/2.6.13.2/misc/ztd-loc.ko
/lib/modules/2.6.13.2/misc/ztd-eth.ko
/lib/modules/2.6.13.2/misc/zaptel.ko
/lib/modules/2.6.13.2/misc/wcusb.ko
/lib/modules/2.6.13.2/misc/wcte11xp.ko
/lib/modules/2.6.13.2/misc/wctdm.ko
/lib/modules/2.6.13.2/misc/wct4xxp.ko
/lib/modules/2.6.13.2/misc/wct1xxp.ko
/lib/modules/2.6.13.2/misc/wcfxo.ko
/lib/modules/2.6.13.2/misc/torisa.ko
/lib/modules/2.6.13.2/misc/tor2.ko
/lib/modules/2.6.13.2/misc/pciradio.ko


(*2)
# cat /proc/zaptel/1
Span 1: WCFXO/0 "Wildcard X101P Board 1"

           1 WCFXO/0/0 FXSKS

(*3)
# cat /etc/zaptel.conf
fxsks=1
loadzone=us
defaultzone=us

# cat /etc/asterisk/zapata.conf
[trunkgroups]
[channels]
;language=en
signalling=fxs_ks
context=x100p-incoming
;usecallerid=yes
;hidecallerid=no
;callwaiting=no
;threewaycalling=yes
;transfer=yes
;echocancel=yes
;echotraining=yes
channel => 1

# cat /etc/asterisk/zapata.conf
...snip...
[x100p-incoming]
; incoming calls from the FXO port are directed to this context from
zapata.conf
exten => s,1,Answer
exten => s,2,Echo

-- 
+------------------------------------------------------------------+
| James   W.   Laferriere | System    Techniques | Give me VMS     |
| Network        Engineer | 3542 Broken Yoke Dr. |  Give me Linux  |
| babydr at baby-dragons.com | Billings , MT. 59105 |   only  on  AXP |
+------------------------------------------------------------------+
_______________________________________________
--Bandwidth and Colocation sponsored by Easynews.com --

Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users