[Asterisk-Users] AVM Fritz! + chan_capi + mISDN + PTP
Lionel Riem
lriem at mac.com
Mon Oct 10 07:56:08 MST 2005
... which is equivalent to my protocol=0x22 ;)
Nevertheless. I think it was a problem with chan_capi being too old
and not supporting protocol=0x22 layermask=0xf (it would not work
without layermask=0xf).
I am currently trying to get it working with chan_misdn. Will let you
know how it goes. It was a pain in the arse to find some document
about how to get it running, so I hope other people may use my
findings somehow.
L. Riem
lriem at mac.com
Le 10 oct. 05 à 16:34, Craig Guy a écrit :
> Hi,
>
> Yes, you can use the Fritz! in PTP mode, though only if you are
> using the mISDN drivers. The mISDN driver should be called like this:
>
> modprobe avmfritz protocol=34
>
> Craig
>
> ----- Original Message ----- From: "Lionel Riem" <lriem at mac.com>
> To: <asterisk-users at lists.digium.com>
> Sent: Monday, October 10, 2005 4:04 PM
> Subject: [Asterisk-Users] AVM Fritz! + chan_capi + mISDN + PTP
>
>
>
>> Hello everyone,
>>
>> I have been using an AVM Fritz! card with chan_capi and mISDN for
>> quite a while in PTM mode and it was working finely.
>>
>> Now, I needed more DID/MSN, so I switched to PTP. But now nothing
>> works anymore :(
>>
>> I am using Asterisk on Debian Sarge stable and installed Asterisk
>> along with chan_capi from apt-get. I installed mISDN from the CVS
>> of isdn4linux.de.
>>
>> It is :
>> - Asterisk 1.0.7 with bristuff
>> - chan_capi 0.3.5
>>
>> When I load the whole modules lot, I get the following in dmesg:
>>
>> Modular ISDN Stack core $Revision: 1.25 $
>> mISDNd: kernel daemon started
>> ISAC module $Revision: 1.16 $
>> mISDNd: test event done
>> CAPI Subsystem Rev 1.1.2.8
>> capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
>> ISDN L1 driver version 1.11
>> ISDN L2 driver version 1.20
>> mISDN: DSS1 Rev. 1.30
>> mISDN Capi 2.0 driver file version 1.14
>> X25 DTE modul version 1.8
>> AVM Fritz PCI/PnP driver Rev. 1.30
>> ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 10 (level, low) -> IRQ 10
>> mISDN_fcpcipnp: found adapter Fritz!Card PCI v2 at 0000:00:14.0
>> fritz card cd09a000 dch cd09a094 bch1 cd09a214 bch2 cd09a3a0
>> AVM PCI V2: stat 0x240020e
>> AVM PCI V2: Class E Rev 2
>> AVM PnP: HDLC version 2
>> mISDN: AVM Fritz!PCIv2 config irq:10 base:0xEC00
>> spin_lock_adr=cd09a024 now(d015b867)
>> busy_lock_adr=cd09a024 now(d015b867)
>> AVM PCI/PnP: reset
>> AVM PCI/PnP: S0/S1 40/2
>> Fritz1 ISAC STAR 40
>> Fritz1 ISAC MODE c0
>> Fritz1 ISAC ADF2 ff
>> Fritz1 ISAC ISTA 0
>> Fritz1 ISAC CIR0 7
>> mISDN_isac_init: ISACSX
>> Fritz1 HDLC 1 STA 82000000
>> Fritz1 HDLC 2 STA 82000000
>> AVM Fritz!PCI: IRQ 10 count 4
>> fritz 1 cards installed
>>
>>
>>
>> Here is my /etc/asterisk/capi.conf:
>>
>> ;
>> ; CAPI config
>> ;
>> ;
>> [general]
>> nationalprefix=0
>> internationalprefix=00
>> rxgain=0.8
>> txgain=0.8
>>
>> [interfaces]
>> mode=immediate
>> isdnmode=ptp
>> msn=*
>> incomingmsn=*
>> controller=1
>> softdtmf=1
>> context=dispatcher
>> accountcode=
>> devices=2
>>
>>
>> Here is my /etc/modprobe.d/capi conf file:
>>
>> alias /dev/capi20 avmfritz
>> alias char-major-68-0 avmfritz
>>
>> install avmfritz /sbin/modprobe capi; \
>> /sbin/modprobe mISDN_core; \
>> /sbin/modprobe mISDN_l1; \
>> /sbin/modprobe mISDN_l2; \
>> /sbin/modprobe l3udss1; \
>> /sbin/modprobe mISDN_capi; \
>> /sbin/modprobe mISDN_x25dte; \
>> /sbin/modprobe --ignore-install avmfritz protocol=0x22
>>
>> remove avmfritz /sbin/modprobe -r --ignore-remove avmfritz; \
>> /sbin/modprobe -r mISDN_x25dte; \
>> /sbin/modprobe -r mISDN_capi; \
>> /sbin/modprobe -r l3udss1; \
>> /sbin/modprobe -r mISDN_l2; \
>> /sbin/modprobe -r mISDN_l1; \
>> /sbin/modprobe -r mISDN_core; \
>> /sbin/modprobe -r capi
>>
>>
>>
>> "capiinfo" shows me:
>>
>> asterisk:/etc/asterisk# capiinfo
>> Number of Controllers : 1
>> Controller 1:
>> Manufacturer: mISDN CAPI controller Fritz1
>> CAPI Version: 2.0
>> Manufacturer Version: 1.0
>> Serial Number: 0002
>> BChannels: 2
>> Global Options: 0x00000018
>> DTMF supported
>> Supplementary Services supported
>> B1 protocols support: 0x00000003
>> 64 kbit/s with HDLC framing
>> 64 kbit/s bit-transparent operation
>> B2 protocols support: 0x00000043
>> ISO 7776 (X.75 SLP)
>> Transparent
>> Transparent (ignoring framing errors of B1 protocol)
>> B3 protocols support: 0x00000005
>> Transparent
>> ISO 8208 (X.25 DTE-DTE)
>>
>> 0100
>> 0200
>> 18000000
>> 03000000
>> 43000000
>> 05000000
>> 00000000 00000000 00000000 00000000 00000000 00000000
>> 00000000 00000000 00000000 00000000 00000000
>>
>> Supplementary services support: 0x00000012
>> Terminal Portability
>> Call Forwarding
>>
>>
>>
>> In Asterisk, when an incoming call arrives, it shows me the
>> following:
>>
>> Asterisk Ready.
>> *CLI> capi info
>> Contr1: 2 B channels total, 2 B channels free.
>> *CLI> capi debug
>> CAPI Debugging Enabled
>> *CLI>
>> *CLI>
>> *CLI> -- INFO_IND ID=001 #0x0001 LEN=0016
>> Controller/PLCI/NCCI = 0x101
>> InfoNumber = 0x18
>> InfoElement = <89>
>>
>> -- INFO_IND ID=001 #0x0001 LEN=0016
>> Controller/PLCI/NCCI = 0x101
>> InfoNumber = 0x18
>> InfoElement = <89>
>>
>> Oct 10 09:17:16 NOTICE[5948]: chan_capi.c:1184 find_pipe: PLCI
>> doesnt match last pipe (PLCI = 0x101)
>> Oct 10 09:17:16 NOTICE[5948]: chan_capi.c:1301 pipe_msg: INFO_IND
>> ID=001 #0x0001 LEN=0016
>> Controller/PLCI/NCCI = 0x101
>> InfoNumber = 0x18
>> InfoElement = <89>
>> -- CONNECT_IND ID=001 #0x0002 LEN=0044
>> Controller/PLCI/NCCI = 0x101
>> CIPValue = 0x1
>> CalledPartyNumber = <81>20
>> CallingPartyNumber = <01 83>0123456789
>> CalledPartySubaddress = default
>> CallingPartySubaddress = default
>> BC = <80 90 a3>
>> LLC = default
>> HLC = default
>> AdditionalInfo
>> BChannelinformation = default
>> Keypadfacility = default
>> Useruserdata = default
>> Facilitydataarray = default
>>
>> Oct 10 09:17:16 NOTICE[5948]: chan_capi.c:1931 capi_handle_msg:
>> CONNECT_IND ID=001 #0x0002 LEN=0044
>> Controller/PLCI/NCCI = 0x101
>> CIPValue = 0x1
>> CalledPartyNumber = <81>20
>> CallingPartyNumber = <01 83>0123456789
>> CalledPartySubaddress = default
>> CallingPartySubaddress = default
>> BC = <80 90 a3>
>> LLC = default
>> HLC = default
>> AdditionalInfo
>> BChannelinformation = default
>> Keypadfacility = default
>> Useruserdata = default
>> Facilitydataarray = default
>>
>> == CONNECT_IND
>> (PLCI=0x101,DID=20,CID=0123456789,CIP=0x1,CONTROLLER=0x1)
>> -- creating pipe for PLCI=0x101 msn = *
>>
>>
>>
>> And it just hangs here. After a little while (10 seconds or so),
>> the other party gets a message from the teclo telling him that
>> "this number cannot receive calls at the moment".
>>
>> I really hope that someone may be able to help me. I am really
>> stuck here and I need to be able to receive calls quite quickly
>> now, as it's my business line.
>>
>> If you need anything else, just let me know.
>>
>> Thanks,
>>
>> L. Riem
>> lriem at mac.com
>>
>>
>> _______________________________________________
>> --Bandwidth and Colocation sponsored by Easynews.com --
>>
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>
> _______________________________________________
> --Bandwidth and Colocation sponsored by Easynews.com --
>
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
More information about the asterisk-users
mailing list