[Asterisk-Users] Hangup Issues on TDM40B FXO Australia

[Haydn.Kemmery at lihir.com.pg]

Thanks
Terry noticed asterisk at home 0.7 will try version 1



-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Terry H.
Gilsenan
Sent: Monday, 23 May 2005 1:35 PM
To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
Subject: RE: [Asterisk-Users] Hangup Issues on TDM40B FXO Australia

Hi,

I have 2 Asterisk servers in .pg and 2 in .au

In .pg I have had to configure them as if they were in .au and use LS
signaling.

I am using the latest Asterisk @ Home (1.0) and it is working well with
1 TDM400P for interfacing with the PSTN lines.

Previously I had exactly the problem you have described using Asterisk @
Home (0.7).

I also had a memory leak problem in that all the memory 512Mb would be
gradually used up and after about 3 days the audio would begin to
suffer.

The upgrade was a full reinstall and rebuild from documentation and once
completed, the problems have not reappeared.

These server are also NTP servers and DHCP servers

Regards,
T

> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of 
> Haydn.Kemmery at lihir.com.pg
> Sent: Monday, 23 May 2005 12:49 PM
> To: asterisk-users at lists.digium.com
> Subject: [Asterisk-Users] Hangup Issues on TDM40B FXO Australia
> 
> Afternoon all, 	
> 
> After doing some test on my asterisk box I can successfully receive 
> calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network
> 
> Dial out from a sip phone is also not an issue, all calls connect and 
> terminate normally.
> 
> If I call the Asterisk PBX say from PSTN in Zap1-1 and out through
> ZAP2-2 back to the PSTN (after entering the correct pin off
> course) the card does not appear to detect the hang-up, I then have to

> issues a soft hang-up to close the call, I presume this indicates the 
> card is configured to receive the correct hangup signal
> 
> I have tried enabling callprogress, busydetect and a few settings on 
> the busycount but to no success
> 
> I've also tried LS and KS signalling
> 
> Does anyone else have any suggestions to get this to work with 
> Australia's Telstra?
> 
> 
> 
> Regards
> 
> Haydn
> 
> 
> 
> 
> 
> 
> --------------------------------------------------------------
> ------------------------------------------------------
> This email and any files transmitted with it are confidential and 
> intended solely for the use of the individual or entity to whom they 
> are addressed.
> If you have received this email in error please notify the originator 
> of the message. This footer also confirms that this email message has 
> been scanned for the presence of computer viruses.
> 
> Any views expressed in this message are those of the individual 
> sender, except where the sender specifies and with authority, states 
> them to be the views of LMC.
> 
> --------------------------------------------------------------
> ------------------------------------------------------
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users

_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users
--------------------------------------------------------------------------------------------------------------------
This email and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom
they are addressed.
If you have received this email in error please notify the
originator of the message. This footer also confirms that this
email message has been scanned for the presence of computer viruses.

Any views expressed in this message are those of the individual
sender, except where the sender specifies and with authority,
states them to be the views of LMC.

--------------------------------------------------------------------------------------------------------------------