[Asterisk-Users] 2 x Eicon BRI ISDN devices (UK)

[asterisk]

MSN will only work on 1 ISDN2 line and cannot be spread across 2 ISDN2
lines. From your description I assume you have 2 calls up and the 3rd call
fails. This is because you can only have 2 concurrent calls using MSN on
ISDN2. You will find you have a different number range for the second ISDN2
If you want to use both ISDN lines for incoming calls with the same number
range then you will need to have the lines converted to 1 + 1 Auxiliary
working and have the numbers delivered as DDI.

Neil

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Lee Norvall
Sent: 18 May 2005 13:27
To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
Subject: RE: [Asterisk-Users] 2 x Eicon BRI ISDN devices (UK)

Hi

I can see what seems to be both devices in use, so I guess it must be
down to the capi.conf (below), does this look correct ???

[interfaces]

msn=292880
incomingmsn=292880, 292881, 292882, 292883, 292884, 292885, 292886,
292887, 292888, 292889
outgoingmsn=292880
controller=1
softdtmf=1
;accountcode=
context=demo
;echosquelch=1
;echocancel=yes
;echotail=64
;callgroup=1
;deflect=12345678
devices=2

msn=292xxx
incomingmsn=292880, 292881, 292882, 292883, 292884, 292885, 292886,
292887, 292888, 292889
outgoingmsn=292880
controller=2
softdtmf=1
;accountcode=
context=demo
;echosquelch=1
;echocancel=yes
;echotail=64
;callgroup=1
;deflect=12345678
devices=2



-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Armin
Schindler
Sent: 18 May 2005 12:50
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] 2 x Eicon BRI ISDN devices (UK)

On Wed, 18 May 2005, Lee Norvall wrote:
> Hi
>  
> I have installed 2 x Eicon BRI ISDN cards into a Suse 9.2 server.  We
can
> use all 4 lines for out going calls fine, but on incoming we can only
use 2.
> On calling in using the main msn, the 3rd line gives a an engaged
signal.
> 
> I have unplugged 1 of the cards, and the other card takes the 2 calls.
I
> then swapped this around, and this also works fine.  But when using
both
> cards, we can only use 2 line in.

There are two possibilities:

1) your Telco doesn't send the 3rd call to your other line.
   You can verify that by using
    divactrl mlog -c 1 -o          (diva_idi module must be leaded)
   and see if an incoming call is shown.
   (use -c 2 for the second card)

2) your configuration of chan_capi is not correct and the 3rd call is 
   ignored/rejected.

If you don't use DIVA Server cards with CAPI, forget this mail.

Armin

_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users


_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users