[Asterisk-Users] cisco 3620 setup (newbie cisco alert)

[Asterisk]

Thanks for that - I've managed to configure the cisco box following 
various examples on the web, but come stuck at the following:

dial-peer voice 100 pots
 application session
 max-conn 30
 destination-pattern 0.........
 translate-outgoing called 1
 no digit-strip
 direct-inward-dial
 port 0:D
 forward-digits all
!

the "port" command does not exist "% Unrecognized command". Show Version gives

#show version    
Cisco Internetwork Operating System Software 
IOS (tm) 3600 Software (C3620-J1S3-M), Version 12.3(13a), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Tue 26-Apr-05 09:12 by ssearch
Image text-base: 0x60008B00, data-base: 0x619C0000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ROM: 3600 Software (C3620-J1S3-M), Version 12.3(13a), RELEASE SOFTWARE (fc2)

delta uptime is 1 hour, 33 minutes
System returned to ROM by reload
System image file is "flash:c3620-j1s3-mz.123-13a.bin"

cisco 3620 (R4700) processor (revision 0x81) with 58368K/7168K bytes of memory.
Processor board ID 24364331
R4700 CPU at 80MHz, Implementation 33, Rev 1.0
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
2 Ethernet/IEEE 802.3 interface(s)
32 Serial network interface(s)
2 Channelized E1/PRI port(s)
DRAM configuration is 32 bits wide with parity disabled.
29K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Any more help appreciated :)

Julian.


barney wrote:

> Your configuration is OK. Cisco is counting from 0, so  Serial 0:15 is 
> 16th channel (D-channel) of first E1 (if you don`t have serial 
> interfaces also...).
> zaptel/asterisk is counting from 1, so 1-16 is D-channel of first E1 
> interface.
>
> See archive for thread named "Asterisk and Cisco AS5300 or 3600". 
> There is example of configuration.
>
> -b
>
>
> ----- Original Message ----- From: "Asterisk" <asterisk at dotr.com>
> To: "Asterisk Users Mailing List - Non-Commercial Discussion" 
> <asterisk-users at lists.digium.com>
> Sent: Monday, May 16, 2005 2:18 PM
> Subject: [Asterisk-Users] cisco 3620 setup (newbie cisco alert)
>
>
>> I'm experimenting (using for the first time) with using a cisco3620 
>> to connect to the PSTN via a channelised E1 interface, with * 
>> handling all of the SIP calls.
>>
>> If anyone has any installation tips / help / documentation I would be 
>> most appreciative :)
>>
>> However, my first question is this: when I am in the setup, I see the 
>> following:
>>
>> Current interface summary
>>
>> Controller Timeslots D-Channel Configurable modes Status
>> E1 0/0     31        15        pri/channelized     Administratively up
>> E1 1/0     31        15        pri/channelized     Administratively up
>>
>> I have set both controllers to hdb3, ccs with crc4
>>
>> I notice that the D-Channel is set to 15. However, in the zaptel.conf 
>> file I use with my TE410p card, the D-Channel is set to 16. So, is 
>> cisco counting 0-14 (hence 15 is the D-Channek) and zaptel counting 
>> from 1-15 (and therefore 16 is the D-channel) ? Or is my config wrong 
>> on the cisco or zaptel ??
>>
>> Any help would be welcome. Thanks !
>>
>> Julian
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>